VeEX VePAL TX300M User Manual Download Page 415

Page: 415 / 421

It is also possible to view and download results from the ReVeal MTX300 software. Please consult the

ReVeal MTX300 Manual

for further instructions.

Go back to top

Go back to TOC

17.2.3 File Management in ReVeal

All files can be managed through the VeEX ReVeal PC Software.

Simply connect the management port of the unit to a PC and launch ReVeal MTX300 on the PC. For further instructions on

managing CPRI test results on ReVeal, including downloading and creating reports, please see

5.0 Results

in the

ReVeal

MTX300 manual

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands