VeEX VePAL TX300M User Manual Download Page 414

Page: 414 / 421

Go back to top

Go back to TOC

17.2.2.6 Saving and Retrieving Files

At any time when the test is in progress or completed, press the

Save

key

on the rubber keypad to save test results.

Use the alphanumeric keyboard to name the file and press

Apply

to save the results and close the keyboard screen.

Saving and Naming Results

To access Saved results, access the

Files

Saved

menu on the left side toolbar.

Scroll down to

CPRI

index.

All previously saved CPRI results are listed. Tap on the results file name to open the file or choose to copy to USB, delete, or

rename the file.

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands