VeEX VePAL TX300M User Manual Download Page 354

Page: 354 / 421

Go back to top

Go back to TOC

15.5.2.4 Saving Throughput (Multiple Streams) Results

Once the test has been stopped the results can be saved by pressing the

Save

key on the VePAL’s keypad. The results will be

saved and named automatically. Once the results are saved, the user may view or rename the results file by going to

Home

Files

Saved

. Please see

10.2 Recalling or Viewing Files and Test Results

in the

V300 Common Functions manual

for

more information.

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands