VeEX VePAL TX300M User Manual Download Page 411

Page: 411 / 421

TX Pattern:

The test pattern being transmitted.

RTD:

If Round Trip Delay measurements are enabled, RTD will be indicated as On and results (Current/Average/Min/Max)

will be displayed. To enable or disable Round Trip Delay measurement, tap on the

RTD On/Off

button

located in the right side column.

Note:

Round Trip Delay measurements require a physical Loopback at the far-end.

Verify that no errors are present and the TX and RX Utilization (%) is at 100%. Press the

Restart

button

if errors

are present.

Round Trip Delay Diagram

Go back to top

Go back to TOC

17.2.2.2 Signal

Signal Diagram

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands