V-ZUG 74A, Instructions Manual

Page: 14 / 218

14
as described in the section “Making coffee using coffee be-
ans”.
Please note: You can make just one coffee at a time by pres-
sing the
button (B4) (fig. 12).
• After using the machine with pre-ground coffee, to go
back to making coffee using beans, disable the pre-ground
coffee function by pressing the
button (B2) (fig. 8)
again.
NOTE 1: Never introduce pre-ground coffee when the machine is
off or it could spread through the inside of the appliance.
NOTE 2: Never add more than 1 measure, otherwise the applian-
ce will not make the coffee.
NOTE 3: Use the measure provided only.
NOTE 4: Introduce only pre-ground coffee for espresso coffee
machines into the funnel.
NOTE 5: If more than one measure of pre-ground coffee is used
and the funnel clogs, push the coffee down with a knife (fig. 21)
then remove and clean the infuser and machine as described in
the “Cleaning the infuser” chapter.
DELIVERING HOT WATER
• Make sure the water spout is in place (fig. 6).
• Position a container under the spout.
• Press the (B6) button (fig. 20).
The message “HOT WATER” is displayed and hot water flows
out of the hot water spout into the container below.
You should not deliver hot water for more than 2 minutes at
a time.
To interrupt the flow, press the button (B6).
The appliance stops delivery once the set quantity is rea-
ched.
CHANGING THE QUANTITY OF HOT WATER
The appliance is set by default to automatically deliver 250 ml.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the button (B6) again until “HOT WATER PRO-
GRAM QUANTITY” is displayed, then release the but-
ton.
3. When the hot water in the cup reaches the required level,
press the button (B6) again.
The machine is now reprogrammed with the new quantity.
MAKING CAPPUCCINO
• Select the taste of the coffee you want to use to make the
cappuccino by pressing the button (B2).
• Remove the lid of the milk container.
• Fill the container with about 100 grams of milk for each
cappuccino to be prepared (fig. 23). Never exceed the MAX
level (corresponding to about 750 ml) marked on the con-
tainer.
You should ideally use skimmed or semi-skimmed milk at
refrigerator temperature (about 5°C).
• Make sure the intake tube is correctly inserted in the rubber
washer (fig. 24) then replace the milk container lid.
Position the froth regulator between the words cappuccino
and caffelatte printed on the milk container lid.
The quantity of froth can be adjusted by moving the regula-
tor towards the word “caffelatte” for a denser froth.
Moving it towards the word “cappuccino” obtains a less
dense froth.
• Remove the hot water spout (fig 6) and attach the milk
container to the nozzle (fig. 25).
• Position the milk tube as shown in fig. 26 and then place a
sufficiently large cup under the coffee and milk spouts.
• Press the button (B8). “CAPPUCCINO” is displayed
and after a few seconds, frothed milk flows out of the milk
spout into the cup below. (Delivery stops automatically).
• The appliance delivers coffee.
• The cappuccino is now ready. Sweeten to taste and, if desi-
red, sprinkle the froth with a little cocoa powder.
NOTE 1: While making cappuccino, the flow of frothed milk or
coffee can be interrupted by pressing the
button (B8).
NOTE 2: If the milk in the container finishes while delivering fro-
thed milk, remove the container and add milk.
Reattach and press the
button (B8) to request a cappuccino
again.
NOTE 3: To ensure the complete cleanliness and hygiene of the
milk frother, always clean the circuits in the milk container lid
after making cappuccino. “PRESS CLEAN” flashes on the display.
• Place a recipient under the milk spout (fig. 26).
• Press the CLEAN button on the lid (C3) and hold down for at
least 5 seconds (fig. 26) to start the cleaning function.
The appliance displays the message “CLEANING UNDER-
WAY” above a progress bar. You should not release the CLE-
AN button until the bar is complete indicating that cleaning
is concluded. When the CLEAN button is released, the fun-
ction stops. After cleaning, remove the milk container and
NO froth
“Less dense” froth
Froth regulator
“Denser” froth