manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

4.30  Fluorescent Lamp 

4  Replacement Procedures 

Setting the bezel 

1.  Start installing the bezel in the upward direction until it stops at the top left corner. 

NOTE:  

The GND-CU and lamp reflector on the left-hand side must not go beyond the 

edges of the bezel. 
Use care not to damage the cables and TAB. 
The bezel latches must be engaged (there are five latches on the top edge, and two latches 
on the bottom edge). 

 

ƒ‰ƒbƒ`‚Q‰ÓŠ —L‚èD

ƒ‰ƒbƒ`‚T‚©Š ‚ð‚Í‚ß‚éD

 Ÿ‚É‚½‚s‚`‚a‘¤‚ð‚Í‚ß‚éD

ƒP[ ƒuƒ‹‚ðƒLƒY‚‚¯‚È‚¢‚悤‚É ’ˆÓ

ƒxƒ[ƒ‹‚ðƒ‰ƒ“ƒv‘¤‚©‚ç‚Í‚ß‚éD

ƒxƒ[ƒ‹‚ÌŠO‚Éo ‚È‚¢‚±‚ÆD

‚f‚m‚c| ‚b‚tÜ ‚è‹È‚˚—L‚èD

ƒxƒ[ƒ‹‚ÌŠO‚Éo ‚È‚¢‚±‚Æ

ƒŠƒtƒŒƒNƒ^Ü ‚è‹È‚˚—L‚èD

2

2

2

2

2

1

Next, fit the bezel’s edge close to the TAB.

Close the five latches.

First, fit the bezel’s edge close to the lamp.

Use care not to damage the cable.

The fold of GND-cu must not go

beyond the bezel’s edge.

The fold of reflector must not go

beyond the bezel’s edge.

Two latches

 

Figure 4-147 Setting the bezel 

Satellite A20 Maintenance Manual (960-444) 

4-189 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Datalogic MEMOR K User Manual preview
MEMOR K
Brand: Datalogic Pages: 88
CompuLab Tensor-I22 Owner'S Manual preview
Tensor-I22
Brand: CompuLab Pages: 19
Acer Power 1000 Guía Del Usuario preview
Power 1000
Brand: Acer Pages: 51
EUROCOM UNO 2.1 User Manual preview
UNO 2.1
Brand: EUROCOM Pages: 271
Vecow ECS-9740-505M-GTX1050 User Manual preview
ECS-9740-505M-GTX1050
Brand: Vecow Pages: 111
Lenze CPC 5100 Operating Instructions Manual preview
CPC 5100
Brand: Lenze Pages: 68
Emerson Rosemount TankRadar SCC 5320 Instruction Manual preview
Rosemount TankRadar SCC 5320
Brand: Emerson Pages: 4
Emerson FloBoss S600 Instruction Manual preview
FloBoss S600
Brand: Emerson Pages: 108
7starlake ROC286AA User Manual preview
ROC286AA
Brand: 7starlake Pages: 31
Toshiba Satellite M100 Series Specifications preview
Satellite M100 Series
Brand: Toshiba Pages: 2
Toshiba Satellite M100 Series User Manual preview
Satellite M100 Series
Brand: Toshiba Pages: 283
Medion AKOYA E2225 D Quick Manual preview
AKOYA E2225 D
Brand: Medion Pages: 2
Medion E27401 Instruction Manual preview
E27401
Brand: Medion Pages: 37
Medion MD8806 Instruction Manual preview
MD8806
Brand: Medion Pages: 68
Avalue Technology FPC-08R1 Quick Reference Manual preview
FPC-08R1
Brand: Avalue Technology Pages: 12
Avalue Technology EMS-SKLU Quick Reference Manual preview
EMS-SKLU
Brand: Avalue Technology Pages: 122
National Instruments VXIpc 700 Series User Manual preview
VXIpc 700 Series
Brand: National Instruments Pages: 80
Optoma OPS2-i7 Quick Install Manual preview
OPS2-i7
Brand: Optoma Pages: 2

Brands by name

Popular brands

Load more brands