manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

4.19  RTC Battery 

4 Replacement Procedures 

4.19  RTC Battery  

WARNING:

  When replacing the RTC battery, be sure to use genuine batteries or 

replacement batteries authorized by Toshiba. Installing the wrong battery could cause a 
battery explosion or other damage. 
 
If the RTC battery is found abnormal, it must not be installed. Replace it with a new 
battery, and dispose of the old one according to the local regulations. 
 
Check for any of the following signs of damage: 
 
1)  

Electrolyte  leakage 

   

•  Corrosion (greenish color) on the battery connector or cable 

   

•  Corrosion on the computer's battery connector 

   

•  White powder on any part of the battery 

   

•  White powder in the battery tray 

   

•  Clear liquid on the battery 

   

•  Clear liquid in the battery tray 

   

•  Clear liquid on any board near the battery 

 
2)  

Damage to the connection cable 

 
3)  

Damage to the connector housing 

 
If any powder or liquid is found in or around the battery tray, clean it. Be careful not to 
let any leaked material contact your eyes or mouth. Do not inhale fumes from leaked 
material. 
 
If leaked material contacts your skin, eyes or mouth, wash the affected area thoroughly 
with clean water. 
 

Satellite A20 Maintenance Manual (960-444) 

4-53 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

A1Touch AOD 260 User Manual preview
AOD 260
Brand: A1Touch Pages: 9
IBM IntelliStation Z Pro 6221 Installation Manual preview
IntelliStation Z Pro 6221
Brand: IBM Pages: 110
ECS LIVA One H310C User Manual preview
LIVA One H310C
Brand: ECS Pages: 53
EUROCOM LP200ST User Manual preview
LP200ST
Brand: EUROCOM Pages: 113
Risecom Corporation RS-3990 User Manual preview
RS-3990
Brand: Risecom Corporation Pages: 32
Aaeon TKS-G50-QM77 Manual preview
TKS-G50-QM77
Brand: Aaeon Pages: 117
XPLORE TECHNOLOGIES iX104C6 Quick Start Manual preview
iX104C6
Brand: XPLORE TECHNOLOGIES Pages: 2
Vizio All-in-One Touch PC Quick Start Manual preview
All-in-One Touch PC
Brand: Vizio Pages: 40
FabiaTech Fanless FX5202 User Manual preview
Fanless FX5202
Brand: FabiaTech Pages: 65
Gateway GT4015H User Manual preview
GT4015H
Brand: Gateway Pages: 346
Acer Veriton X680G Service Manual preview
Veriton X680G
Brand: Acer Pages: 84
Casio PB-1000 Owner'S Manual preview
PB-1000
Brand: Casio Pages: 143
ABB mFLOG5 Application Manual preview
mFLOG5
Brand: ABB Pages: 16
ABB Totalflow G5 Series Application Manual preview
Totalflow G5 Series
Brand: ABB Pages: 20
ABB XSeries G4 6200 User Manual preview
XSeries G4 6200
Brand: ABB Pages: 168
IEI Technology DRPC-240-TGL User Manual preview
DRPC-240-TGL
Brand: IEI Technology Pages: 50
Sony Vaio VPCJ115FX/B Specifications preview
Vaio VPCJ115FX/B
Brand: Sony Pages: 2
Sony Vaio VPCJ112GX/B Specifications preview
Vaio VPCJ112GX/B
Brand: Sony Pages: 2

Brands by name

Popular brands

Load more brands