Toshiba Satellite A20 Series Maintenance Manual Download Page 22

Page: 22 / 495

1 Hardware Overview

1.2 System Unit Block Diagram

The system unit is composed of the following major components:

Processor

Intel Desktop Pentium

Processor 2.53GHz

– Processor

core

speed: 2.53GHz at 1.525V

– Processor bus speed: 533MHz
– Integrated L1 cache memory: 12KB instruction cache and 8KB write-back

data cache, 4-way set associative

– Integrated L2 cache memory: 512KB ECC protected cache data array, 8-

way set associative

– Integrated

NDP

Intel Desktop Pentium

Processor 2.66GHz

– Processor

core

speed: 2.66GHz at 1.525V

– Processor bus speed: 533MHz
– Integrated L1 cache memory: 12KB instruction cache and 8KB write-back

data cache, 4-way set associative

– Integrated L2 cache memory: 512KB ECC protected cache data array, 8-

way set associative

– Integrated

NDP

Intel Desktop Pentium

Processor 2.8GHz

– Processor

core

speed: 2.8GHz at 1.525V

– Processor bus speed: 533MHz
– Integrated L1 cache memory: 12KB instruction cache and 8KB write-back

data cache, 4-way set associative

– Integrated L2 cache memory: 512KB ECC protected cache data array, 8-

way set associative

– Integrated

NDP

Intel Desktop Pentium

Processor 3.06GHz

– Processor

core

speed: 3.06GHz at 1.525V

– Processor bus speed: 533MHz
– Integrated L1 cache memory: 12KB instruction cache and 8KB write-back

data cache, 4-way set associative

– Integrated L2 cache memory: 512KB ECC protected cache data array, 8-

way set associative

– Integrated

NDP

1-8

Satellite A20 Maintenance Manual (960-444)

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Search results

Summary of Contents for Satellite A20 Series

Reviews:

Toshiba Satellite A20 Series, Maintenance Manual, Page: 22 / 495

Search results

Summary of Contents for Satellite A20 Series

Reviews: