manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

2.12  Sound Troubleshooting 

2  Troubleshooting Procedures 

Table 2-3  Printer port LED boot mode status (1/8) 

LED Status 

Test item 

Message 

 

 

Register initialization for boot block 

Clearing software reset bit 

Permitting A20 line 

FFh Start 

Initialization of special register and Intel chip set 

PIT CH0 initialization (for HOLD ON) 

BIOS rewrite flag initialization 

Checksum check 

Transition to protected mode 

B0h 

Flash ROM check 

Boot block checksum check (The system halts 
when a checksum error is detected.) 

Transition to BIOS rewriting when rewrite is 
requested 
Executing KBC initialization sequence 

Enabling keyboard 

B1h 

EC/KBC rewrite check 

[Tilde], [TAB] key check 

BIOS rewrite request check when check sum error 
except for Boot Block is detected, or rewrite is 
requested by user 

B2h 

BIOS rewrite check 

Transition to BIOS rewrite 

System BIOS rewrite 
transition to IRT 

System BIOS rewrite transition to IRT 

Hardware initialization 

Setting base for Power Management I/O Space 

Enabling BIOS write 

Special interrupt control 

Disabling BIOS write protect 

Enabling SMBus I/O space 

Enable SMBus access 

Opening work I/O for SDRAM initialization 

Setting FDC prohibition 

Hardware initialization for each model 

PIT CH1 initialization (setting refresh interval to 30 
m/s) 

B3h 

BIOS rewrite process 

Initialization of PIT, DMAC, PIC 

 

Satellite A20 Maintenance Manual (960-444) 

 

2-23 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

C&T VCO-6020-1050TI User Manual preview
VCO-6020-1050TI
Brand: C&T Pages: 79
ECS LIVA One H310C User Manual preview
LIVA One H310C
Brand: ECS Pages: 53
Artila Matrix-604 User Manual preview
Matrix-604
Brand: Artila Pages: 16
Compaq Presario 3500 Series Maintenance & Service Manual preview
Presario 3500 Series
Brand: Compaq Pages: 68
Compaq Deskpro Series Getting Started preview
Deskpro Series
Brand: Compaq Pages: 20
Ocean Systems RackMount Quick Start Manual preview
RackMount
Brand: Ocean Systems Pages: 2
Vizio All-in-One Touch PC Quick Start Manual preview
All-in-One Touch PC
Brand: Vizio Pages: 40
Morrow Tricep Installation Manual preview
Tricep
Brand: Morrow Pages: 162
MSI AP190 User Manual preview
AP190
Brand: MSI Pages: 53
Dell Latitude 3440 Owner'S Manual preview
Latitude 3440
Brand: Dell Pages: 57
Dell Insprion 8100 Setup Manual preview
Insprion 8100
Brand: Dell Pages: 80
Dell OptiPlex SX260 Setup And Quick Reference Manual preview
OptiPlex SX260
Brand: Dell Pages: 112
Dell OptiPlex 5250 Owner'S Manual preview
OptiPlex 5250
Brand: Dell Pages: 78
Dell OptiPlex 3240 Owner'S Manual preview
OptiPlex 3240
Brand: Dell Pages: 57
Dell OptiPlex FX170 Quick Setup Manual preview
OptiPlex FX170
Brand: Dell Pages: 144
Dell OptiPlex 5480 All-in-One Service Manual preview
OptiPlex 5480 All-in-One
Brand: Dell Pages: 102
Dell OptiPlex 160L Service Manual preview
OptiPlex 160L
Brand: Dell Pages: 16
Dell OptiPlex E1 Reference And Installation Manual preview
OptiPlex E1
Brand: Dell Pages: 158

Brands by name

Popular brands

Load more brands