manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

2  Troubleshooting Procedures  

2.12  Sound Troubleshooting

 

Procedure 2 

Printer Port LED Check on Boot Mode 

The printer port LED displays the IRT status and test status by turning lights on and off as an 
eight-digit binary value for boot mode.  Figure 2-2 shows the printer port LED. 

 

 

 

Figure 2-2 Printer port LED 

To use the printer port LED, follow the steps below: 

1.  Plug the printer port LED into the computer’s parallel port. 

2.  Turn on the computer’s power. 

3.  Read the LED status from left to right as you are facing the back of the computer. 

4.  Convert the status from binary to hexadecimal notation. 

5.  If the final LED status is FFh (normal status), go to Procedure 3. 

6.  If the final LED status matches any of the test status values in Table 2-3, perform Check 

1. 

NOTE

:  If an error condition is detected by the IRT test, the printer port LED displays an 

error code after the IRT test ends.  For example, when the printer port LED displays 19h and 
halts, the IRT test has already completed the Display initialization.  In this instance, the IRT 
indicates an error has been detected during the Display logo. 

 

2-22 

Satellite A20 Maintenance Manual (960-444) 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

DIVERSIFIED WOODCRAFTS 2810K Series Assembly Instructions Manual preview
2810K Series
Brand: DIVERSIFIED WOODCRAFTS Pages: 18
Workrite Solace Sit-to-Stand Premium Assembly/Installation Instructions preview
Solace Sit-to-Stand Premium
Brand: Workrite Pages: 2
StarTech.com ARMSTS Instruction Manual preview
ARMSTS
Brand: StarTech.com Pages: 29
Vector VIP System Overview Manual preview
VIP
Brand: Vector Pages: 32
Vxl Itona Md75 Installation Manual preview
Itona Md75
Brand: Vxl Pages: 29
Sony VAIO VPCSA21GXSI Specifications preview
VAIO VPCSA21GXSI
Brand: Sony Pages: 4
Sony VAIO VPCSA21GXBI Specifications preview
VAIO VPCSA21GXBI
Brand: Sony Pages: 4
Sony VAIO VPCL237FX/B Specification Sheet preview
VAIO VPCL237FX/B
Brand: Sony Pages: 2
Sony VAIO VPCL22DFX/B Specification Sheet preview
VAIO VPCL22DFX/B
Brand: Sony Pages: 3
Sony Vaio VPCL116FX/B Specifications preview
Vaio VPCL116FX/B
Brand: Sony Pages: 2
Sony VAIO VPCL222FX/B Specification Sheet preview
VAIO VPCL222FX/B
Brand: Sony Pages: 3
Sony VAIO VPCL223FX/B Specification Sheet preview
VAIO VPCL223FX/B
Brand: Sony Pages: 3
Sony VAIO VPCL224FX/B Specification Sheet preview
VAIO VPCL224FX/B
Brand: Sony Pages: 3
Sony VAIO VPCL22CFX/B Specification Sheet preview
VAIO VPCL22CFX/B
Brand: Sony Pages: 4
Sony Vaio VPCJ11CFX/B Specifications preview
Vaio VPCJ11CFX/B
Brand: Sony Pages: 2
Sony Vaio VPCJ11AFX/B Specifications preview
Vaio VPCJ11AFX/B
Brand: Sony Pages: 2
Sony Vaio VPCJ11BFX/B Specifications preview
Vaio VPCJ11BFX/B
Brand: Sony Pages: 2
Sony Vaio VPCJ117FX/B Specifications preview
Vaio VPCJ117FX/B
Brand: Sony Pages: 2

Brands by name

Popular brands

Load more brands