manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

4  Replacement Procedures 

4.30  Fluorescent Lamp 

8.  Install the bezel (E) on the lamp cover. Attach the four latches on the lamp cover and 

two latches on the P-chassis.  

 

(E)  Bezel

(2)  Lean the bezel on the lamp cover

without interference with  the TCP.

(1)  Hitch the hook of the bezel

on the rib of the P-chassis.

< Side view >

Hook

(Lamp cover side)

 

Figure 4-132  Replacing Sharp fluorescent lamp (SXGA+) (20) 

 

4-174 

Satellite A20 Maintenance Manual (960-444) 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Olivetti M20 Hardware Reference Manual preview
M20
Brand: Olivetti Pages: 254
Samsung CLP 600N - Color Laser Printer Manual preview
CLP 600N - Color Laser Printer
Brand: Samsung Pages: 23
Gardena FlexControl 1883 Operation Instructions Manual preview
FlexControl 1883
Brand: Gardena Pages: 19
GARANT eLevel User Manual preview
eLevel
Brand: GARANT Pages: 60
Avid Technology Dell T7600 Configuration Manuallines preview
Dell T7600
Brand: Avid Technology Pages: 23
LDI Spaces SAFCO MUV 1926 Assembly Instructions preview
SAFCO MUV 1926
Brand: LDI Spaces Pages: 5
Avid Technology HP Z220 Configuration Manuallines preview
HP Z220
Brand: Avid Technology Pages: 19
Dell OptiPlex 7080 Micro Service Manual preview
OptiPlex 7080 Micro
Brand: Dell Pages: 57
HP b2600 Supplementary Manual preview
b2600
Brand: HP Pages: 108
HP Bc1500 - BladeSystem - Blade PC Setup And Installation Manual preview
Bc1500 - BladeSystem - Blade PC
Brand: HP Pages: 149
HP Compaq 18 All-in-One Product End-Of-Life Disassembly Instructions preview
Compaq 18 All-in-One
Brand: HP Pages: 13
HP Compaq d538 CMT Hardware Reference Manual preview
Compaq d538 CMT
Brand: HP Pages: 80
HP Compaq 303B Product End-Of-Life Disassembly Instructions preview
Compaq 303B
Brand: HP Pages: 7
HP Compaq dc7800 MT Technical Reference Manual preview
Compaq dc7800 MT
Brand: HP Pages: 102
HP Compaq dx7510 Service & Reference Manual preview
Compaq dx7510
Brand: HP Pages: 105
HP bc1000 Series Reference Manual preview
bc1000 Series
Brand: HP Pages: 22
HP Compaq dc7800 Series Reference Manual preview
Compaq dc7800 Series
Brand: HP Pages: 276
HP Compaq dc7700 Ultra Slim Desktop (USDT) Business Product End-Of-Life Disassembly Instructions preview
Compaq dc7700 Ultra Slim Desktop (USDT) Business
Brand: HP Pages: 10

Brands by name

Popular brands

Load more brands