manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

4.30  Fluorescent Lamp 

4  Replacement Procedures 

2.  Remove the screws (E) on both sides. 

The maximum allowed releasing torque is

0.1078N

¥

m (1.1kgf

¥

cm).

 

Figure 4-151  Removing the screws from the sides 

3.  Flip the module over again (with the top of the module facing up) and remove the two 

latches that are close to the lamp. 

Latch

 

Figure 4-152  Removing the latches close to the lamp 

Satellite A20 Maintenance Manual (960-444) 

4-193 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Panasonic CF-51 Series Supplementary Instructions Manual preview
CF-51 Series
Brand: Panasonic Pages: 12
Panasonic CF-30 Series Supplementary Instructions Manual preview
CF-30 Series
Brand: Panasonic Pages: 16
Panasonic CF-17 Operating Instructions Manual preview
CF-17
Brand: Panasonic Pages: 28
Panasonic CF-07 Series Reference Manual preview
CF-07 Series
Brand: Panasonic Pages: 43
ADLINK Technology MXC-2300 Manual preview
MXC-2300
Brand: ADLINK Technology Pages: 76
IBM System x3200 M3 Product Manual preview
System x3200 M3
Brand: IBM Pages: 42
Uplift Desk UDA110 Instructions preview
UDA110
Brand: Uplift Desk Pages: 2
NovaSail NS360 Operating Manual preview
NS360
Brand: NovaSail Pages: 32
Fujitsu Siemens Computers SCALEO EVi 2565 Datasheet preview
SCALEO EVi 2565
Brand: Fujitsu Siemens Computers Pages: 2
IEI Technology WAFER-BT-i1 Quick Installation Manual preview
WAFER-BT-i1
Brand: IEI Technology Pages: 14
Nexcom NISE 51 User Manual preview
NISE 51
Brand: Nexcom Pages: 85
Shuttle DS20U Series Quick Manual preview
DS20U Series
Brand: Shuttle Pages: 3
KAUKO XI-M User Manual preview
XI-M
Brand: KAUKO Pages: 14
AMSTRAD GX4000 User Instructions preview
GX4000
Brand: AMSTRAD Pages: 45
Aaeon ACP-5185 Manual preview
ACP-5185
Brand: Aaeon Pages: 106
XDS Sigma 2 Reference Manual preview
Sigma 2
Brand: XDS Pages: 63
Quanmax QBOX-2080 Series User Manual preview
QBOX-2080 Series
Brand: Quanmax Pages: 42
Tandy TRS-80 Model 16 Service Manual preview
TRS-80 Model 16
Brand: Tandy Pages: 92

Brands by name

Popular brands

Load more brands