manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

3.6  Keyboard Test 

3  Tests and Diagnostics 

If the test ends successfully, OK is displayed. If nothing 

is displayed, there may be a problem with the USB port. 

Check the wraparound connection and repeat the test. 

To check only the USB mouse, follow the procedures below: 

Connect the USB mouse to the computer’s USB connector. 

Next, set up the computer’s hardware as follows: 

PERIPHERAL 

 

Pointing Devices = Simultaneous 

 

USB Legacy Emulation = Enabled 

Then, perform the Pointing Stick Diagnostic Test and make sure: 

• 

The cursor moves in the direction that you move the USB mouse. 

• 

The display reverses when you click the right button or left button 

To stop this test, press the two IPS buttons on the computer (connected to 
PJ10) at the same time. (You cannot use the USB mouse to stop the test.) 

Subtest 08 

CD-function key test 

When this subtest displays a message shown below, press [MODE] button for 
3 seconds to release the key lock. 

Press [MODE Control] Button 

 

CAUTION

:  You cannot continue the test if the key lock is not released. 

 

When this subtest displays messages shown below, press the corresponding  
CD-function key.  

NOTE

:  This subtest must be completed within 10 seconds. 

 

Press [play/pause] Button 

Press [stop] Button 

Press [rewind] Button 

Press [forward] Button 

Satellite A20 Maintenance Manual (960-444)

 3-17 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Olivetti M20 Hardware Reference Manual preview
M20
Brand: Olivetti Pages: 254
Sinclair Spectrum 128 Service Manual preview
Spectrum 128
Brand: Sinclair Pages: 65
Quanmax QDSP-300 User Manual preview
QDSP-300
Brand: Quanmax Pages: 37
Compaq Presario 3500 Series Maintenance & Service Manual preview
Presario 3500 Series
Brand: Compaq Pages: 68
Stage right 600039 User Manual preview
600039
Brand: Stage right Pages: 12
Intel NUC7CJYH Manual preview
NUC7CJYH
Brand: Intel Pages: 2
ACE COMPUTERS Firestorm 1Z490X Technical Reference Manual preview
Firestorm 1Z490X
Brand: ACE COMPUTERS Pages: 42
Compaq Compaq Evo D310 MT Hardware Reference Manual preview
Compaq Evo D310 MT
Brand: Compaq Pages: 57
Fellowes Lotus VE Manual preview
Lotus VE
Brand: Fellowes Pages: 42
Cybernet ZPC-GX31 User Manual preview
ZPC-GX31
Brand: Cybernet Pages: 47
Shuttle XPC slim XH510G2 Quick Manual preview
XPC slim XH510G2
Brand: Shuttle Pages: 3
DLoG MPC 6 Manual preview
MPC 6
Brand: DLoG Pages: 223
Shuttle XPC SD32G2 User Manual preview
XPC SD32G2
Brand: Shuttle Pages: 38
Shuttle XPC SS59G User Manual preview
XPC SS59G
Brand: Shuttle Pages: 64
Shuttle XPC SN26P User Manual preview
XPC SN26P
Brand: Shuttle Pages: 68
Shuttle XPC SD31P User Manual preview
XPC SD31P
Brand: Shuttle Pages: 79
W&T rule.box 53920 Operating Instructions Manual preview
rule.box 53920
Brand: W&T Pages: 30
Shuttle P20U Bios Manual preview
P20U
Brand: Shuttle Pages: 24

Brands by name

Popular brands

Load more brands