manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual, Page: 136 / 495

Share
Download
Toshiba Satellite A20 Series Maintenance Manual Download Page 136

3  Tests and Diagnostics 

3.9  Printer Test 

3.9 Printer 

Test 

To execute the Printer Test, select

 6

 from the DIAGNOSTIC TEST MENU, press 

Enter

 

and 

follow the directions on the screen. The Printer Test contains three subtests that test the 
output of the printer connected to the computer. The following messages will appear after 
selecting the Printer Test from the DIAGNOSTIC TEST MENU. Answer each of the 
questions with an appropriate response to execute the test. 

NOTE

: A Port Replicator and an IBM compatible printer must be connected to the system 

to execute this test.  

The following message will appear when the printer test is selected: 

channel#1 = XXXXh 

channel#2 = XXXXh 

channel#3 = XXXXh 

Select the channel number (1-3) ? 

The printer I/O port address is specified by the XXXXh number. The computer supports 
three printer channels. Select the printer channel number, and press 

Enter

 

to execute the 

selected subtest. 

Subtest 01 

Ripple Pattern 

This subtest prints characters for codes 20h through 7Eh line-by-line while 
shifting one character to the left at the beginning of each new line. 

 

3-24  

Satellite A20 Maintenance Manual (960-444) 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments