Home
/
Toshiba
/
Satellite A20 Series
/
Maintenance Manual

Toshiba Satellite A20 Series, Maintenance Manual, Page: 116 / 495

Share

Page: 116 / 495

Toshiba Satellite A20 Series Maintenance Manual Download Page 116

3 Tests and Diagnostics

3.2 Executing the Diagnostic Test

2. To execute the DIAGNOSTIC TEST MENU from the DIAGNOSTICS MENU, set

the highlight bar to

1,

and press

Enter

. The following DIAGNOSTIC TEST MENU

will appear:

TOSHIBA Personal Computer XXXX DIAGNOSTICS

Version XXX (c) Copyright TOSHIBA Corp. XXXX

DIAGNOSTIC TEST MENU :
1 - SYSTEM TEST

2 - MEMORY TEST

3 - KEYBOARD TEST

4 - DISPLAY TEST

5 – FLOPPY DISK TEST

6 – PRINTER TEST

7 – ASYNC test

8 - HARD DISK TEST

9 - REAL TIMER TEST

10 - NDP TEST

11 - EXPANSION TEST

12 -

13 – CD-ROM/DVD-ROM TEST

14 –

88 - ERROR RETRY COUNT SET [FDD & HDD]

99 - EXIT TO DIAGNOSTICS MENU

Refer to sections 3.4 through 3.15 for detailed descriptions of each Diagnostic Tests 1

through 13. Function 88 sets the floppy disk drive and hard disk drive error retry
count. Function 99 exits the submenus of the Diagnostic Test and returns to the
Diagnostic Menu.

3-4

Satellite A20 Maintenance Manual (960-444)

«
...
114
115
116
117
118
...
»

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments