manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual, Page: 157 / 495

Share
Download
Toshiba Satellite A20 Series Maintenance Manual Download Page 157

3   Tests and Diagnostics 

3.18  Sound/LAN/Modem Test 

Subtest 01 

Microphoned recording & play 

 

This subtest checks the function of the CODEC A/D D/A converter. Both the 
microphone and headphone terminal can be checked at the same time. 

 

Before executing this subtest, connect an external microphone to the computer. 
IF necessary, connect a headphone to the computer to check whether the 
headphone jack of the computer is working properly. 

 

When the subtest is selected, the following message appears. 

 

Copyright (C) 2000 Acer Laboratories Inc. All Rights Reserved. 

 

Record Parameters : 

         Wave Channel Index = 31 (d) 

         Wave File Name     = Record.wav 

         Recording Length   = 3 (d) sec 

         PCM Sample Rate    = 11000 (d) 

         PCM Sample Size    = 8 (d) 

         PCM Tone Type      = 2 (d) 

         Record Input       = Mic-In 

         SPDIF In Option    = 0 (d) 

         Play Volume Gain   = 11 (d) 

         Record Volume Gain = 15 (d) 

 

When "SPDIF" is "On", Options Listed Below Will Be Ignored: 

        "Play Volume Gain" 

        "Record Volume Gain" 

 

Recording... (Press "s" to Stop) 

ALi Audio Device Record Wave File Done !!! 

 

The sound is recorded for five seconds automatically from the microphone. 
After the recording is completed, the computer immediately plays back the 
sound recorded. When the playing is finished, a message similar to the one 
below appears. 

3-46  

Satellite A20 Maintenance Manual (960-444)

 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments