manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

Appendix H   EC/KBC Rewrite Procedures 

Appendices

 

Appendix H  

 

Appendix H  EC/KBC Rewrite Procedures 

This Appendix explains how to rewrite the EC/KBC system program when you update the 
EC/KBC system. 

Tools 

 

To rewrite the EC/KBC, you need the following tool: 

 

BIOS/EC/KBC rewriting disk for the computer 

Rewriting the EC/KBC

 

NOTE:

  1.  Rewrite the EC/KBS only when instructed by a diagnostic disk release 

notice. 

 

2.  Connect the AC adaptor to the computer when you rewrite the EC/KBC. 

 

3.  Do not turn off the power while you are rewriting the EC/KBC. 

If the rewrite fails, it might be impossible to start up the computer. 

 

4.  If  you fail to rewrite EC/KBC, then when you next turn on the power, a 

message may be displayed that the contents of the EC/KBC has been erased.  
In this case, insert the BIOS/EC/KBC rewriting disk, and the EC/KBC will 
be rewritten. 

 

5.  Normally it takes about 30 seconds to rewrite the EC/KBC.  It may take 3 

minutes (maximum), depending on the conditions of the computer or ICs. 
The computer is not hung up.  Allow sufficient time.  Never reboot or turn 
off the power to the computer before the rewriting is completed. 

1.  Set the system to boot mode. 
2.  Turn off the power to the computer. 
3.  Remove the external cable and PC Card. 
4.  Insert the BIOS/EC/KBC rewriting disk into the built-in FDD. 
5.  Turn on the power while holding down the 

Tab 

key.  (Keep holding down the key 

until a message appears on the screen.)  The BIOS/EC/KBC rewriting starts. 

6.  When the EC/KBC rewrite is completed, the system is automatically turned off. 

Satellite A20 Maintenance Manual (960-444) 

 H-1 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

DATA FROM SKY TrafficXRoads Manual preview
TrafficXRoads
Brand: DATA FROM SKY Pages: 40
IBM AT 5170 Technical Reference preview
AT 5170
Brand: IBM Pages: 500
M5Stack POECAM Manual preview
POECAM
Brand: M5Stack Pages: 15
Digital Equipment STARION 200i Service Maintenance Manual preview
STARION 200i
Brand: Digital Equipment Pages: 96
thomann Millenium Studio Desk WS20 Assembly Instructions preview
Millenium Studio Desk WS20
Brand: thomann Pages: 2
WalkAbout Hammerhead 3 User Manual preview
Hammerhead 3
Brand: WalkAbout Pages: 30
Dell PowerEdge 4400 Owner'S Manual preview
PowerEdge 4400
Brand: Dell Pages: 148
Dell P82G Quick Start Manual preview
P82G
Brand: Dell Pages: 18
Acer Aspire M3910 Service Manual preview
Aspire M3910
Brand: Acer Pages: 74
Acer Aspire M3900 Service Manual preview
Aspire M3900
Brand: Acer Pages: 83
Acer Aspire M5810 User Manual preview
Aspire M5810
Brand: Acer Pages: 77
Acer Aspire M5810 Service Manual preview
Aspire M5810
Brand: Acer Pages: 97
Acer Aspire M3710 Service Manual preview
Aspire M3710
Brand: Acer Pages: 73
Acer Aspire T630 User Manual preview
Aspire T630
Brand: Acer Pages: 28
Acer Aspire M5802 Service Manual preview
Aspire M5802
Brand: Acer Pages: 105
Acer Aspire M3920 Service Manual preview
Aspire M3920
Brand: Acer Pages: 98
Acer Aspire T671 (Spanish) Guía Del Usuario preview
Aspire T671
Brand: Acer Pages: 30
Acer Aspire TC-865 User Manual preview
Aspire TC-865
Brand: Acer Pages: 52

Brands by name

Popular brands

Load more brands