Toshiba Satellite A20 Series Maintenance Manual Download | Manualshive

Page: 15 / 495

background image

1.1 Features

1 Hardware Overview

1 Features

1.1 Features

The Toshiba Satellite A20 Personal Computer uses extensive Large Scale Integration (LSI),
and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide
compact size, minimum weight, low power usage and high reliability. The computer is built
and configured to order, to best meet the customer’s needs. This computer incorporates the
following features:

Processor

Intel Desktop Pentium

4

Processor

•

The processor runs at one of the following speeds:

–  2.53GHz (1.525volts) / 533MHz
–  2.66GHz (1.525volts) / 533MHz
–  2.80GHz (1.525volts) / 533MHz
–  3.06GHz (1.525volts) / 533MHz

The processor incorporates a 12KB L1 cache memory and 512KB L2 cache
memory.

Memory

The computer contains no on-board memory.
Two PC2100 (266MHz) compatible DDR-SDRAM slots are available for installation
of a 128MB, 256MB, 512MB or 1GB memory module, for a total of 2GB.

HDD

Single 30GB, 40GB, 60GB or 80GB internal drive, 2.5-inch and 9.5 mm height.

USB FDD

A 3.5-inch USB FDD accommodates both 2HD (1.44MB) and 2DD (720KB) disks.

Satellite A20 Maintenance Manual (960-444)

1-1

«
...
13
14
15
16
17
...
»

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Brand: IBM Pages: 158

Brand: NEC Pages: 146

Compute Stick STK1A32SC

Brand: Intel Pages: 11

Brand: S&T embedded Pages: 23

Brand: Aaeon Pages: 64

Brand: Vecow Pages: 144

Brand: Precision Pages: 5

Brand: AWOW Pages: 4

Brand: Control Data Corporation Pages: 150

Brand: Moxa Technologies Pages: 65

QBiX-Pro-KBLB7100H-A1

Brand: GIGAIPC Pages: 72

Brand: Corvus systems Pages: 19

Brand: AOpen Pages: 24

Brand: AOpen Pages: 23

Brand: Nabu Pages: 355

Brand: HCL Pages: 10

Brand: Cybernet Pages: 40

Brand: Cybernet Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands