Toshiba Satellite A20 Series Maintenance Manual Download Page 153 | Manualshive

Page: 153 / 495

background image

3 Tests and Diagnostics

3.17 Wireless LAN Test (Atheros)

3.17 Wireless LAN Test (Atheros)

This section describes how to perform the wireless LAN transmitting-receiving test with the
test program.

Note:

Use another computer (with Atheros wireless LAN card) that can communicate by
the wireless LAN as a responder machine to perform this test.

In this test, the following items are tested:

* Test PC [Initiator] side

(1) SKU (destination code) check
(2) Mac Address check
(3) Communication test (802.11a Main antenna)
(4) Communication test (802.11a Sub antenna)
(5) Communication test (802.11b)

* [Responder] side

(1) Communication test (802.11b)

This program conducts the above test items continuously and displays results for each item
during the test. However, only the last result for the whole test shall be checked. (The message
"OK" or "NG" is displayed.)

When an "NG" item is detected during the test, the message "NG" is displayed on the screen
and the test stops.

Note:

This program takes a long time until the test ends.

To start the Wireless LAN test program, follow the steps below:

Note:

Before starting the wireless LAN test, make sure the Wireless Communication
Switch on the left side of the computer is turned on. (The Wireless Communication
LED lights orange.)

3-42

Satellite A20 Maintenance Manual (960-444)

«
...
151
152
153
154
155
...
»

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Brand: IBM Pages: 170

Brand: IBM Pages: 257

Brand: IBM Pages: 63

Brand: Tandy Pages: 138

Brand: @Xi Computer Corporation Pages: 118

Brand: Tangent Pages: 2

Decision Mate V

Brand: NCR Pages: 426

Brand: ADLINK Technology Pages: 76

Brand: DFI Pages: 15

Brand: Commodore Pages: 31

Evo Desktop Series

Brand: Compaq Pages: 30

Brand: Advantech Pages: 68

Brand: Fujitsu Pages: 8

Brand: Fujitsu Pages: 13

ESPRIMO P910 E85+

Brand: Fujitsu Pages: 10

Brand: Fujitsu Pages: 10

Brand: Fujitsu Pages: 14

Brand: Fujitsu Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands