manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

2  Troubleshooting Procedures  

2.3  Power Supply Troubleshooting

 

Procedure 3 

Connection Check 

The power supply wiring diagram is shown below: 

 

Battery pack 

AC

adapter 

System board 

AC power cord 

AC adapter cord

 

 
Any of the connectors may be disconnected.  Perform Check 1. 

Check 1  Disconnect the AC power cord from wall outlet.  Check the power cable for breaks.  

If the power cord is damaged, connect a new AC power cord.  If there is no damage, 
go to Check 2. 

Check 2  Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC IN 

15 V socket, AC adaptor inlet and wall outlet.  If these cables are connected correctly, 
go to Check 3. 

Check 3  Use a multimeter to make sure that the AC adaptor output voltage is close to 15 V.  If 

the output is several percent lower than 15 V, go to Check 4.  If the output is close to 
15 V, go to Check 5. 

Check 4  Connect a new AC adaptor or AC power cord.  

•

  If the DC IN LED does not light, go to Procedure 5. 

•

  If the battery LED does not light, go to Check 5. 

Check 5  Make sure the battery pack is installed in the computer correctly.  If the battery is 

properly installed and the battery LED still does not light, go to Procedure 4.  

2-16 

Satellite A20 Maintenance Manual (960-444) 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

TES IEC-22 User Manual preview
IEC-22
Brand: TES Pages: 45
Acnodes RMC8416 Installation Manual preview
RMC8416
Brand: Acnodes Pages: 10
Simrad MARINE COMPUTER - INSTALLATION REV A Installation Manual preview
MARINE COMPUTER - INSTALLATION REV A
Brand: Simrad Pages: 40
Fujitsu ESPRIMO Q5 Series Operating Manual preview
ESPRIMO Q5 Series
Brand: Fujitsu Pages: 61
CONNECTA HEF644 Instruction Manual preview
HEF644
Brand: CONNECTA Pages: 4
BELL LABS INNOVATIONS Lucent Technologies CentreVu Sun Ultra 5 Connectivity Diagram preview
Lucent Technologies CentreVu Sun Ultra 5
Brand: BELL LABS INNOVATIONS Pages: 8
Shuttle X27 Series Quick Manual preview
X27 Series
Brand: Shuttle Pages: 1
Shuttle SX58H7 User Manual preview
SX58H7
Brand: Shuttle Pages: 64
Shuttle SH510000.100 User Manual preview
SH510000.100
Brand: Shuttle Pages: 27
Shuttle DL20N Series User Manual preview
DL20N Series
Brand: Shuttle Pages: 25
AST PREMMIA GL Series Operator'S Manual preview
PREMMIA GL Series
Brand: AST Pages: 95
Acer Aspire E5-574 User Manual preview
Aspire E5-574
Brand: Acer Pages: 77
BCP SKY1172 Instruction Manual preview
SKY1172
Brand: BCP Pages: 8
MSI B450M PRO-VDH MAX Manual preview
B450M PRO-VDH MAX
Brand: MSI Pages: 34
Texas Instruments Business System 300A Operator'S Manual preview
Business System 300A
Brand: Texas Instruments Pages: 125
Dynamic SFC332L Operator'S Manual preview
SFC332L
Brand: Dynamic Pages: 148
Aaeon FOX-120 User Manual preview
FOX-120
Brand: Aaeon Pages: 32
IBM Types 2193 User Manual preview
Types 2193
Brand: IBM Pages: 214

Brands by name

Popular brands

Load more brands