Toshiba Satellite A20 Series Maintenance Manual Download Page 139 | Manualshive

Page: 139 / 495

background image

3.11 Hard Disk Test

3 Tests and Diagnostics

3.11 Hard Disk Test

To execute the Hard Disk Test, select

8

from the DIAGNOSTIC TEST MENU, press

Enter

,

and follow the directions on the screen. The hard disk test contains ten subtests that test the
hard disk drive functions.

NOTE

: To execute the subtest 02,03,04,06,09 or 10, the system requires you to enter

password.
The contents of the hard disk will be erased when the subtest 02, 03, 04, 06,09,
or 10 is executed. Before running the test, the customer should transfer the
contents of the hard disk to floppy disk. If the customer has not or cannot
perform the back-up, create back-up disks as described below.

Check to see if the Microsoft Create System Disks Tools (MSCSD.EXE) still

exists in the System Tools Folder. (This tool can be used only once.) If it exists,

use it to back up the pre-installed software, then use the Backup utility in the

System Tools folder to back up the entire disk, including the user’s files.

Refer to the operating system instructions.

After selecting the hard disk test from the DIAGNOSTIC TEST MENU, answer each of the
questions with an appropriate response to execute the test.

1. Select the hard disk drive number to be tested.

Test drive number select (1:HDD#1, 2:HDD#2, 0:HDD1&2)

2. This message is used to select the retry operation when the hard disk controller

detects an error. Select

yes

or

no

.

HDC F/W error retry (1:yes, 2:no) ?

3. This message is used to select the error dump operation when a data compare error is

detected. Select

yes

or

no

.

Data compare error dump (1:yes, 2:no) ?

This message is used to select whether or not the HDD status is displayed on
the screen. The HDD status is described in section 3.19. Select

yes

or

no

.

Detail status display (1:yes, 2:no) ?

5. The Hard Disk Test message will appear after you respond to the Detail Status

prompt. Select the number of the subtest you want to execute and press

Enter.

The

following message will appear during each subtest.

Satellite A20 Maintenance Manual (960-444)

3-27

«
...
137
138
139
140
141
...
»

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Brand: Xerox Pages: 20

Brand: IBM Pages: 158

Desktop Hardware

Brand: Digiop Pages: 2

Brand: Displays2go Pages: 2

Brand: Texim Europe Pages: 5

ThinkCentre 8105

Brand: IBM Pages: 38

Brand: Gigabyte Pages: 2

SPARC classic X

Brand: Sun Microsystems Pages: 198

Brand: IBM Pages: 194

Brand: Aaeon Pages: 55

Brand: MSI Pages: 36

Brand: QNAP Pages: 43

Brand: GIGAIPC Pages: 70

XPC slim DL10J Series

Brand: Shuttle Pages: 25

Brand: WAGO Pages: 50

Brand: I-Tech Pages: 39

Brand: Safco Pages: 2

Deep Learning Box Rack

Brand: CADnetwork Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands