Toshiba Satellite A20 Series Maintenance Manual Download Page 402 | Manualshive

Page: 402 / 495

background image

4.30 Fluorescent Lamp

4 Replacement Procedures

4. Attach the protection cover S (A), protection cover G (B), aluminum tape (C), tape

for lead fixing (D), and aluminum shield (K). All of which must be new ones.
Attach the protection cover (A) then cover (B), using the engaging pins as the guide.
Fold the ends of the covers toward the side of the bezel.

•

When attaching the aluminum tape (C)

−

Align a longer side with the marking on the lamp cover on the reverse
side of the bezel.

−

Align a shorter side with the edge of the lamp cover.

When attaching the tape for lead fixing (D)

Align a longer side with the marking on the lamp cover on the reverse
side of the bezel.

−

Align a shorter side with the location where the head of the screw is
covered.

When attaching the retention tape (H)

−

Align both a longer and a shorter sides with the rectangular hole.

•

When attaching the aluminum shield (K)

Align the corner of shield with the module corner.

Engaging pins

Rectangular hole

Figure 4-158 Attaching the protection cover and tapes

Satellite A20 Maintenance Manual (960-444)

4-197

«
...
400
401
402
403
404
...
»

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Brand: IAC INDUSTRIES Pages: 11

Staff Workstation 795

Brand: 3M Pages: 6

Dynapro ET 3200 Series

Brand: 3M Pages: 21

Brand: Igel Pages: 2

Brand: iDOT Pages: 66

Brand: Igel Pages: 2

Brand: Radio Shack Pages: 52

Brand: Avalue Technology Pages: 78

FieldGo PCATX-R9

Brand: BSi Pages: 40

Kontron KWS 3000-CML

Brand: S&T Pages: 58

Brand: RKM Pages: 33

Brand: Moxa Technologies Pages: 53

Brand: HCL Pages: 8

Brand: Shuttle Pages: 1

Brand: AMSTRAD Pages: 229

DRIVE TWO PLUS 1500

Brand: RACORE COMPUTERS Pages: 66

Brand: MeLe Pages: 4

Brand: ACD Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands