manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

 

 

Satellite A20 Maintenance Manual (960-444) 

iii 

Preface 

This maintenance manual describes how to perform hardware service maintenance for the 
Toshiba Personal Computer Satellite A20 Series, referred to as A20 Series in this manual. 

The procedures described in this manual are intended to help service technicians isolate 
faulty Field Replaceable Units (FRUs) and replace them in the field. 

SAFETY PRECAUTIONS 

Four types of messages are used in this manual to bring important information to your 
attention.  Each of these messages will be italicized and identified as shown below. 

DANGER:  

“Danger” indicates the existence of a hazard that could result in death or 

serious bodily injury, if the safety instruction is not observed. 

 

WARNING:  

“Warning” indicates the existence of a hazard that could result in bodily 

injury, if the safety instruction is not observed. 

 

CAUTION:  

“Caution” indicates the existence of a hazard that could result in property 

damage, if the safety instruction is not observed. 

 

NOTE:

  “Note” contains general information that relates to your safe maintenance 

service. 

 

Improper repair of the computer may result in safety hazards. Toshiba requires service 
technicians and authorized dealers or service providers to ensure the following safety 
precautions are adhered to strictly. 

 

Be sure to fasten screws securely with the right screwdriver. If a screw is not fully 
fastened, it could come loose, creating a danger of a short circuit, which could cause 
overheating, smoke or fire. 

 

If you replace the battery pack or RTC battery, be sure to use only the same model 
battery or an equivalent battery recommended by Toshiba. Installation of the wrong 
battery can cause the battery to explode. 

 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Panasonic CF-30 Series Operating Instruction preview
CF-30 Series
Brand: Panasonic Pages: 15
IBM 5150 Hardware Reference Manual preview
5150
Brand: IBM Pages: 393
Advantech AIM-68 Series User Manual preview
AIM-68 Series
Brand: Advantech Pages: 31
NEC POWERMATE P - SERVICE 1996 Service And Reference Manual preview
POWERMATE P - SERVICE 1996
Brand: NEC Pages: 178
EUROCOM LP295UB User Manual preview
LP295UB
Brand: EUROCOM Pages: 176
Cartft CALUCORE-M Assemly Tutorial preview
CALUCORE-M
Brand: Cartft Pages: 10
MiTAC Master MP1-11TGS Series Getting Started With preview
Master MP1-11TGS Series
Brand: MiTAC Pages: 2
Oracle MICROS Compact Workstation 310 Quick Assembly Manual preview
MICROS Compact Workstation 310
Brand: Oracle Pages: 2
AB Quality 6155R-NSXPH Installation Instructions Manual preview
6155R-NSXPH
Brand: AB Quality Pages: 24
Dell Inspiron 7500 System Reference Manual preview
Inspiron 7500
Brand: Dell Pages: 165
Advanced Micro Computers AmZ8000 User Manual preview
AmZ8000
Brand: Advanced Micro Computers Pages: 77
Sony VAIO PCG-V505DC2 Series Specifications preview
VAIO PCG-V505DC2 Series
Brand: Sony Pages: 2
Sony VAIO MX PCV-MXS10 Specifications preview
VAIO MX PCV-MXS10
Brand: Sony Pages: 1
Sony VAIO Fit 14 Quick Start Manual preview
VAIO Fit 14
Brand: Sony Pages: 2
Sony VAIO E Series SVE111 Quick Start Manual preview
VAIO E Series SVE111
Brand: Sony Pages: 2
Sony VAIO PCG-C1MW Service Manual preview
VAIO PCG-C1MW
Brand: Sony Pages: 11
Sony VAIO PCG-TR3 Series Service Manual preview
VAIO PCG-TR3 Series
Brand: Sony Pages: 17
Sony VAIO PCG6C1L Quick Start Manual preview
VAIO PCG6C1L
Brand: Sony Pages: 44

Brands by name

Popular brands

Load more brands