manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual, Page: 68 / 495

Share
Download
Toshiba Satellite A20 Series Maintenance Manual Download Page 68

2  Troubleshooting Procedures  

2.3  Power Supply Troubleshooting

 

Procedure 5 

Replacement Check 

The system board or the battery board may be disconnected or damaged.  Disassemble the 
computer following the steps described in Chapter 4, 

Replacement Procedures

.  Check the 

connection between the AC adaptor and the system board and connection between the system 
board and the battery board.  After checking the connection, perform the following Check 1: 

Check 1  Replace the AC adaptor with a new one.  If the AC adaptor is still not functioning 

properly, perform Check 2. 

Check 2  Use a multimeter to make sure that F5602, F5603 and F8800 fuses on the system 

board are not blown. If a fuse(s) is not blown, go to Check 3.  If a fuse(s) is blown, go 
to Check 4. 

Check 3  Use a multimeter to make sure that F8810 fuse on the battery board are not blown. If 

the fuse is not blown, go to Check 4. If the fuse is blown, replace the battery board 
with a new one following the instructions in Chapter 4. 

Check 4  The battery board or system board may be damaged.  Replace it with a new one 

following the instructions in Chapter 4. 

 

2-18 

Satellite A20 Maintenance Manual (960-444) 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments