Toshiba Satellite A20 Series Maintenance Manual Download Page 17 | Manualshive

Page: 17 / 495

background image

1.1 Features

1 Hardware Overview

Display

The following displays are available:

14.1-inch XGA TFT screen, 1,024

×

768 pixels, 16M colors

•
•
•

15.0-inch XGA TFT screen, 1,024

×

768 pixels, 16M colors

15.0-inch SXGA+ TFT screen, 1,400

×

1,050 pixels, 16M colors

A video controller contained on the north bridge and 4MB, 8MB, 16MB or
32MB of SMA VRAM enable an external monitor with an RGB cable to display
64k colors at a resolution of 1,600 x 1,200 pixels.

Batteries

The computer has two batteries: a lithium-ion main battery pack and RTC battery
(that backs up the Real Time Clock and CMOS memory).

Slot for optional memory

Two DDR-SDRAM (PC2100) slots are available for 128MB, 256MB, 512MB and
1GB memory modules, consisting of SDRAM chips.

Universal Serial Bus (USB)

The computer comes with three USB 2.0 ports that comply with Enhanced Host
Controller Interface (EHCI) and Open Host Controller Interface (OHCI). The USB
enables daisy-chain connection of up to 127 USB-equipped devices and 480Mbps
serial data transfer. It is designed for easy configuration by a Plug-and-Play operating
system and provides hot insertion/ejection capability.

Infrared port

The infrared port is compatible with Fast InfraRed (FIR) standards enabling cableless
1.15 Mbps, 4 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data
transfer with Infrared Data Association (IrDA) 1.1 compatible external devices.

Internal LAN

The computer is equipped with LAN circuits that support Ethernet LAN (10 megabits
per second, 10BASE-T) and Fast Ethernet LAN (100 mega bits per second, 100
BASE-Tx). It also supports Wakeup on LAN (WOL) and Magic Packet.

Satellite A20 Maintenance Manual (960-444)

1-3

«
...
15
16
17
18
19
...
»

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Personal Computer

Brand: IBM Pages: 318

Brand: IBM Pages: 164

6219 - IntelliStation M - Pro

Brand: IBM Pages: 154

Brand: IBM Pages: 72

Desktop 5130DQ-IL

Brand: Supermicro Pages: 107

TIGW1U - Carrier Grade Server

Brand: Intel Pages: 11

Brand: Commodore Pages: 31

Millenium Studio Desk WS20

Brand: thomann Pages: 2

Brand: Fujitsu Pages: 38

Brand: Fujitsu Pages: 9

Brand: Fujitsu Pages: 10

Esprimo E5 Series

Brand: Fujitsu Pages: 73

DESKPOWER N300 Series

Brand: Fujitsu Pages: 61

Brand: Fujitsu Pages: 56

Brand: Fujitsu Pages: 50

ESPRIMO D5 Series

Brand: Fujitsu Pages: 83

ESPRIMO E420 E85+

Brand: Fujitsu Pages: 8

Brand: Fujitsu Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands