manualshive.com logo in svg

Toshiba Satellite A20 Series, Maintenance Manual

The Toshiba Satellite A20 Series is a versatile laptop that offers exceptional performance and mobility. To ensure easy maintenance and repairs, we provide comprehensive Field Replaceable Unit Documentation in the form of user manuals. These manuals can be downloaded free of charge from our website, making it convenient for users to troubleshoot and optimize their device's performance.

Share
Download
background image

2  Troubleshooting Procedures  

2.12  Sound Troubleshooting

 

Procedure 2 

Connector Check 

The sound function wiring diagram is shown below: 

 

Sound board

PJ6000

PJ9600

PJ9601

MDC

Line In

PJ3010

External microphone

Headphone

PJ6004

PJ6001

System board

PJ9511

PJ9512

PJ9513

PJ9510

Speaker (Right)

Speaker (Left)

SD card

PJ2130

 

Any of the connections may be disconnected. Disassemble the computer following the steps 
described in Chapter 4, 

Replacement Procedures

 and perform the following checks: 

If the speakers don't work correctly, perform Check 1. 

If the external microphone or the headphone doesn't work correctly, perform Check 2. 

 

Check 1  If the speakers don't sound properly, the speaker cable may be disconnected. Make 

sure the speaker cable is firmly connected to PJ9512 and PJ9513 on the system board. 
If the stereo speakers are still not functioning properly, go to Procedure 3. 

Check 2  If the external microphone or the headphone does not work correctly, the cable may 

be disconnected. Make sure PJ9600 and PJ9601 on the sound board is firmly 
connected to PJ9511 and PJ9510 on the system board. If the external microphone or 
the headphone is still not functioning properly, go to Procedure 3. 

2-56 

Satellite A20 Maintenance Manual (960-444) 

Summary of Contents for Satellite A20 Series
















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A20 Series

Acewell ACE-6000 Series User Manual preview
ACE-6000 Series
Brand: Acewell Pages: 2
EUROCOM UNO 2.1 User Manual preview
UNO 2.1
Brand: EUROCOM Pages: 271
Gateway UC73 Reference Manual preview
UC73
Brand: Gateway Pages: 144
Neoware eon 5000 Series User Manual preview
eon 5000 Series
Brand: Neoware Pages: 40
Vecow ECS-9740-505M-GTX1050 User Manual preview
ECS-9740-505M-GTX1050
Brand: Vecow Pages: 111
LG PC100 Easy Setup Manual preview
PC100
Brand: LG Pages: 24
LG PC500-A Series Owner'S Manual preview
PC500-A Series
Brand: LG Pages: 41
LG XPS 8500 Owner'S Manual preview
XPS 8500
Brand: LG Pages: 136
J2 Integrated Touchscreen Computer J2 650 System Manual preview
Integrated Touchscreen Computer J2 650
Brand: J2 Pages: 78
NCD Explora 400 Series Installing Instructions preview
Explora 400 Series
Brand: NCD Pages: 62
NComputing L300 User Manual preview
L300
Brand: NComputing Pages: 95
NCR RealPOS 70XRT User Manual preview
RealPOS 70XRT
Brand: NCR Pages: 183
Sony VAIO VPCSA21GXSI Specifications preview
VAIO VPCSA21GXSI
Brand: Sony Pages: 4
Sony VAIO VPCSA21GXBI Specifications preview
VAIO VPCSA21GXBI
Brand: Sony Pages: 4
Sony VAIO VPCL237FX/B Specification Sheet preview
VAIO VPCL237FX/B
Brand: Sony Pages: 2
Sony VAIO VPCL22DFX/B Specification Sheet preview
VAIO VPCL22DFX/B
Brand: Sony Pages: 3
Sony Vaio VPCL116FX/B Specifications preview
Vaio VPCL116FX/B
Brand: Sony Pages: 2
Sony VAIO VPCL222FX/B Specification Sheet preview
VAIO VPCL222FX/B
Brand: Sony Pages: 3

Brands by name

Popular brands

Load more brands