SL-19
Keyless Entry System
SECURITY AND LOCKS
8
. CHECK ROOM LIGHT OPERATION
9. CHECK HAZARD LIGHT OPERATION
Step
Check
Yes
No
1
CHECK ROOM LIGHT OPERATION.
Make sure the room light illuminates when the
room light switch is turned ON.
Does the room light illuminate? Go to step
2
.
Check the room
light circuit.
2
CHECK HARNESS BETWEEN ROOM LIGHT
AND BODY INTEGRATED UNIT.
1) Disconnect the body integrated unit harness
connector (B280) and room light harness con-
nector (R52).
2) Measure the resistance between the body
integrated unit harness connector terminal and
room light harness connector terminal.
Connector & terminal
(B280) No. 3 — (R52) No. 2:
Is the resistance less than 10
Ω
? The room light
operation circuit is
OK.
Check the harness
for open or short
between body inte-
grated unit and
room light.
Step
Check
Yes
No
1
CHECK HAZARD LIGHT OPERATION.
Make sure the hazard light blinks when hazard
switch is turned to ON.
Does the hazard light blink?
Go to step
2
.
Check the hazard
light circuit.
2
CHECK OUTPUT TO HAZARD LIGHT.
1) Turn the ignition switch to OFF.
2) Disconnect the key warning switch harness
connector.
3) Connect the Subaru Select Monitor to data
link connector.
4) Turn the ignition switch to ON.
5) Select {Integ. unit} from main menu.
6) Select {ECU customizing}.
7) Check {Hazard answer-back setup}, and
then switch to ON setting if necessary.
8) Select the {Current Data Display & Save}.
9) When operate the LOCK/UNLOCK button
of transmitter, check the hazard output signal of
body integrated unit.
Is output signal is present when
operating the transmitter
LOCK/UNLOCK button?
Go to step
3
.
Check the body
integrated unit.
<Ref. to
LAN(diag)-2, Basic
Diagnostic Proce-
dure.>
3
CHECK CIRCUIT OF HAZARD LIGHT.
1) Disconnect the harness connector of body
integrated unit (B280).
2) Disconnect the turn signal and hazard unit
harness connector (R32).
3) Measure the resistance between harness
connector terminals.
Connector & terminal
(B280) No. 12 — (B32) No. 8:
Is the resistance less than 10
Ω
? Check the body
integrated unit.
<Ref. to
LAN(diag)-2, Basic
Diagnostic Proce-
dure.>
Repair the har-
ness.
asieps_tobira.book 19 ページ 2012年2月10日 金曜日 午後3時26分
Summary of Contents for B9 TRIBECA WX 2007
