Smiths Medical 2120 Operator'S Manual Download Page 83

Page: 83 / 152

Operating the Pump

ting

the P
ump

Prime Tubing

When priming the fluid path, the tubing downstream of the pump is filled with fluid, removing any air

bubbles. Prime the tubing

before

connecting it to the patient’s infusion set or indwelling catheter.

Fluid delivered by priming is subtracted from the reservoir volume, but is not added to the amount given

because this fluid is not delivered to the patient. Priming is not allowed when the reservoir volume is 0 mL.

NOTE:

The air detector is disabled while the pump is priming.

NOTE:

If the fluid path contains an air eliminating filter, it is acceptable for air bubbles to be present

on the vent side of the filter. See the instructions for use supplied with the disposable sets for more

information.

Prime Tubing After Changing a Cassette

NOTE:

If you are not changing the cassette but wish to prime the fluid path, use the

Prime Tubing, No

Cassette Change

task described on page 84.

1. When a cassette is attached after the pump is powered on, a

Prime Tubing?

screen always appears.

When priming security is set to On

under patient permissions, a screen

similar to the one on the right appears, and a security code is required

to proceed. If you do not have permission to prime the tubing or if the

tubing is pre-primed, select

No.

For additional information, see

Patient

Permissions

on page 100.

If you have permission to prime the tubing, select

Yes.

Unlock the

keypad.

When priming security is set to Off

under patient permissions, a screen

like the one to the right appears. Select

Yes.

2. If you have not already done so, disconnect the tubing from the patient,

open the clamps, and select

Prime.

WARNING:

Do not prime the fluid path with the tubing connected

to a patient as this could result in overdelivery of medication

or air embolism, which could result in serious patient injury or

death.

3. Stop priming at any time by selecting

Stop Priming.

Priming

automatically stops after 10 mL (or 20 mL if a high volume set is

attached) are primed. Continue priming as needed.

WARNING:

To prevent air embolism, ensure that the entire fluid

path is free of all air bubbles before connecting to the patient.

Air embolism could result in serious patient injury or death.

Summary of Contents for 2120

























































































































































Search results

Summary of Contents for 2120

Reviews:

Related manuals for 2120

Brands by name

Popular brands

Smiths Medical 2120, Operator'S Manual

Search results

Summary of Contents for 2120

Reviews:

Related manuals for 2120

Brands by name

Popular brands