Raven SmarTrax MD Calibration & Operation Manual Download Page 74

Page: 74 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

ROUTINE OPERATION

ENGAGING SMARTRAX MD

FIGURE 42. SmarTrax MD System Engaged

The steering wheel icon in the lower right corner of the Viper Pro screen indicates whether the SmarTrax MD

system is engaged or disengaged. The steering wheel is green when the system is enabled and gray when it is not.

SmarTrax MD can be engaged in two ways:
• Via the Viper Pro by pressing the steering wheel icon in the lower right corner of the display.
• By tapping the foot/enable switch.

SYSTEM SETTINGS

System Setting

Average

Setting

Suggested

Range

Function

Line Acquisition (LA)

Aggressiveness

5 to 13

The LA Aggressiveness value affects how

quickly the machine steers toward a displayed

guidance line when it is traveling further than

24 inches [60 cm] from the desired path.

OnLine (OL) Sensitivity

4 to 13

The OL Sensitivity value affects the response of

the machine while steering within 24 inches [60

cm] of the displayed guidance line.

System Setting

Average

Setting

Acceptable

Range

Function

Zero Yaw

-2 to 2

Indicates amount error in the internal yaw

sensor while no yaw motion is present.

Message Frequency - GGA

and VTG

10 Hz

Displays the frequency of GGA messages from

the GPS receiver.

Not Enabled

Enabled

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands