Raven SmarTrax MD Calibration & Operation Manual Download Page 109

Page: 109 / 136

P/N 016-5030-020 Rev. D

103

TROUBLESHOOTING

SMARTRAX MD OPERATION

Torque H

SmarTrax MD has detected a current

draw greater than 8 amps.

Check the mechanical drive system for

binding conditions.

1. Navigate to the SmarTrax Manual Steering

screen.

2. Toggle the master switch on and off,

verifying that the Raven LED logo

changes from white steady to blue

steady.

3. Drive the motor at various settings while

monitoring the Actual Current value. If no

current is drawn and the problem persists,

replace the mechanical drive.

Wrong HDW

The software and hardware versions of

the node are not compatible.

Update the node software to the proper

version.

Yaw Error

Yaw rate sensor values are out of range.

Replace the SmarTrax node.

Problem

Possible Cause

Corrective Action

SmarTrax MD will not power up.

The power connections are loose

or not properly connected.

Check the power connections to

ensure they are secure and

properly connected.

A fuse is blown.

Replace the fuse.

The battery connections are loose,

corroded, or not properly

connected.

Check the battery connections to

ensure they are secure and

properly connected.

The machine does not have proper

voltage to run the system.

Test for +12VDC using a voltmeter.

The field computer is defective.

Replace the field computer.

SmarTrax MD will not engage by

pressing the foot/enable switch.

The node is not communicating

properly.

Check the LEDs on the node to

ensure proper communication.

There is an active error in the

SmarTrax MD system.

Refer to Error Messages section on

page 100 to troubleshoot the error

message.

The foot/enable switch cable is not

connected or is faulty.

Check the foot/enable switch cable

connection.

The operator presence switch or

jumper plug is disconnected.

Check the operator presence

switch connections.

The SmarTrax MD master switch is

in the “OFF” position.

Manually toggle the master switch

to the “ON” position.

There is no guidance line set.

Set a new guidance line.

Message

Possible Cause

Corrective Action

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Raven SmarTrax MD, Calibration & Operation Manual, Page: 109 / 136

Search results

Summary of Contents for SmarTrax MD

Reviews: