Raven SmarTrax MD Calibration & Operation Manual Download Page 91

Page: 91 / 136

P/N 016-5030-020 Rev. D

ENVIZIO PRO AND CRUIZER II CONSOLES CALIBRATION AND OPERATION

FIGURE 23. Steering Switch Calibration Screen

1. Review the on-screen instructions and turn the steering wheel to verify proper operation.

NOTE:

The SmarTrax MD Setup Wizard will automatically advance to the next step in the calibration process

when the steering wheel is turned. If it does not, refer to Chapter 6, Troubleshooting for

troubleshooting information. If the problem persists, contact your local Raven dealer for further

information.

2. Proceed

to the Engage Switch Calibration section below to continue with the SmarTrax MD system calibration.

ENGAGE SWITCH CALIBRATION

FIGURE 24. Engage Switch Calibration Screen

1. Review the on-screen instructions.
2. Press and release the foot switch or engage switch.

NOTE:

The SmarTrax MD Setup Wizard will automatically advance to the next step in the calibration process

when the engage switch it detected.

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Raven SmarTrax MD, Calibration & Operation Manual, Page: 91 / 136

Search results

Summary of Contents for SmarTrax MD

Reviews: