Raven SmarTrax MD Calibration & Operation Manual Download Page 105

Page: 105 / 136

CHAPTER

P/N 016-5030-020 Rev. D

CHAPTER 6

TROUBLESHOOTING

NODE

The SmarTrax MD CAN control node features several green light-emitting diodes (LEDs) which may be used to

diagnose issues within the SmarTrax MD system.

NOTE:

If the LEDs are not displayed as outlined in the figure below or are all on continuously, check the CAN

connections and the control cable connections on the node. If the issue persists, contact your local

Raven dealer for additional technical support.

FIGURE 1. SmarTrax MD CAN Control Node LEDs

LOGIC POWER - Lit when +12 V

current is supplied to the node.
HC (High Current) POWER - Lit when

High Current Power is supplied to the

node.
MICRO 1 Hz - Flashes once every

second during processor activity.

CAN RX - Flashes to indicate CAN or

Cruizer II messages are being received

by the node. This light typically flashes

rapidly.
CAN TX - Flashes to indicate CAN or

Cruizer messages are being

transmitted from the node. The flash

speed of this light varies.
DIAG 1 - Indicates the node is

receiving valid GGA messages. This

light must be lit in order to engage

SmarTrax. This light cannot be used to

verify that the field computer is

receiving GPS signals.

DIAG 2 - Lit when the 3D terrain

compensation is activated, but does

not indicate 3D terrain compensation

is actively receiving GPS signal for

correction. To verify 3D terrain

compensation is engaged, access the

3D terrain compensation menu on the

field computer.

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands