Raven SmarTrax MD Calibration & Operation Manual Download Page 11

Page: 11 / 136

CHAPTER

P/N 016-5030-020 Rev. D

CHAPTER 2

INTRODUCTION

Congratulations on your purchase of the Raven SmarTrax MD system! This system is designed to provide cutting-

edge, hands-free steering of the machine via Global Positioning System (GPS) coordinates.

The instructions in this manual are designed to assist in the proper calibration and operation of the SmarTrax MD

system when used with the Viper 4, Viper Pro, Envizio Pro or Envizio Pro II, and Cruizer II field computers.

IMPORTANT:

Installation of the SmarTrax MD system must be completed before calibrating the system. If you have

questions regarding the installation of the SmarTrax MD system, refer to the SmarTrax MD Installation

Manual provided with the installation kit.

IMPORTANT:

The Raven field computer/controller must be calibrated specifically for the vehicle before being used to

operate the SmarTrax MD system. For questions about the field computer, refer to the Installation &

Operation Manual provided with the field computer.

NOTE:

Machine-specific installation kits are not available for all machine makes and models.

SMARTRAX MD PART IDENTIFICATION

Latch

Road Switch

Status Indicator

Node Harness

Connection Port

Anti-Rotation Pin

Installation

Locations

Front

Back

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Raven SmarTrax MD, Calibration & Operation Manual, Page: 11 / 136

Search results

Summary of Contents for SmarTrax MD

Reviews: