Raven SmarTrax MD Calibration & Operation Manual Download Page 82

Page: 82 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

FIGURE 6. Machine Type Screen

7. Select the specific machine type from the

Machine Type

list. If the specific machine is not listed, choose the

profile that best fits the machine:

NOTE:

Cruizer II only - If the Machine Type list is not populated fully or at all, press the

Previous

(left) arrow

to reload the screen.

•

SP Sprayer RBoom - Self-propelled sprayer with a rear boom

•

FS Tractor - Front-steered tractor

•

Articulated

•

Track

•

Rear Steered - Rear-steered machine

•

Swather

NOTE:

The Machine Test option should only be selected if calibration problems are encountered. Contact

your local Raven dealer for assistance with using the Machine Test option.

8. Select

Next

FIGURE 7. Steering Control Driving Device Selection Screen

NOTE:

The steering control device selection screen will be displayed only when a SmarTrax node is detected

in the system.

9. Select

SmarTrax MD

in the Control Device drop-down field.

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Raven SmarTrax MD, Calibration & Operation Manual, Page: 82 / 136

Search results

Summary of Contents for SmarTrax MD

Reviews: