manualshive.com logo in svg

Raven SmarTrax MD, Calibration & Operation Manual, Page: 4 / 136

Share
Download
Raven SmarTrax MD Calibration & Operation Manual Download Page 4

Table of Contents

ii

SmarTrax™ MD Calibration & Operation Manual

System Settings   ..................................................................................................................................................................

39

Chapter 4 

Viper Pro Calibration and Operation ..............................................................  

41

Introduction .................................................................................................................................................................

41

Software Compatibility ......................................................................................................................................................

41

SmarTrax MD Status Display ...........................................................................................................................................

41

Initial Startup ...............................................................................................................................................................

42

SmarTrax MD Terms of Use .............................................................................................................................................

42

GPS Configuration ...............................................................................................................................................................

42

Machine Configuration ......................................................................................................................................................

43

Calibration Warning  .....................................................................................................................................

43

Set Up Machine Profile(s) - Optional .....................................................................................................

44

Machine-Specific Configuration ..............................................................................................................

44

Calibrate the SmarTrax MD System ...................................................................................................................

47

Node Orientation .................................................................................................................................................................

47

Configuring Wheel Base and Antenna Offsets .........................................................................................................

47

Enhanced Tilt Calibration ..................................................................................................................................................

52

Steering Switch Calibration ..............................................................................................................................................

55

Engage Switch Calibration ................................................................................................................................................

56

Wheel Angle Sensor (SPS) Calibration .........................................................................................................................

56

Calibrate the Machine’s Steering System ........................................................................................................

57

Complete the SmarTrax MD Calibration Process ..........................................................................................

59

Advanced Setup Tools .............................................................................................................................................

60

Line Acquisition (LA) Mode and Aggressiveness .....................................................................................................

61

On-Line (OL) Mode and Sensitivity ...............................................................................................................................

61

STX Setup Screen .................................................................................................................................................................

62

Sys Diag Screen ....................................................................................................................................................................

63

Adv Setup Screen .................................................................................................................................................................

66

Enhanced Tilt Setup Screen .............................................................................................................................................

67

Routine Operation ....................................................................................................................................................

68

Engaging SmarTrax MD .....................................................................................................................................................

68

System Settings   ..................................................................................................................................................................

68

Chapter 5 

Envizio Pro and Cruizer II Consoles Calibration and Operation...............  

71

Introduction .................................................................................................................................................................

71

Software Compatibility ......................................................................................................................................................

71

SmarTrax MD Status Display ...........................................................................................................................................

71

Initial Startup ...............................................................................................................................................................

72

Cruizer II - Connecting to SmarTrax MD via CAN Communication ..................................................................

72

Envizio Pro ..............................................................................................................................................................................

73

Data Transfer ...................................................................................................................................................

73

GPS Configuration .........................................................................................................................................

73

SmarTrax MD Terms of Use .......................................................................................................................

74

Machine Configuration ......................................................................................................................................................

74

Set Up Machine Profile(s) - Optional .....................................................................................................

74

Machine-Specific Configuration ..............................................................................................................

75

Calibrate the SmarTrax MD System ...................................................................................................................

77

Summary of Contents for SmarTrax MD









































































































































Reviews:

No comments