Raven SmarTrax MD Calibration & Operation Manual Download Page 12 | Manualshive

Page: 12 / 136

background image

C

HAPTER

2

6

SmarTrax™ MD Calibration & Operation Manual

INSTALLATION

RECOMMENDATIONS

Before installing the SmarTrax MD system, park the machine where the ground is level, clean, and dry. Leave the

machine turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this

manual as you complete the installation process.

POINT OF REFERENCE

The instructions in this manual assume that you are standing behind the machine, looking toward the cab.

UPDATES

UPDATING THE NODE

The SmarTrax node may be updated in two ways:
• Via a USB drive loaded with the latest software and plugged into the field computer.
• Via the Raven Service Tool. Refer to the Raven Service Tool Installation & Operation Manual (P/N 016-5030-

022) for instructions on updating the node software.

Refer to the appropriate field computer manual for instructions on updating the node software:
• Viper/Viper 4+ Installation & Operation Manual (P/N 016-0171-539)
• Viper Pro Installation and Operation Manual (P/N 016-0171-122)
• Envizio Pro & Envizio Pro II Installation and Operation Manual (P/N 016-0171-148)
• Cruizer II Operation Guide (P/N 016-0171-415)

UPDATING THE MECHANICAL DRIVE

Update the mechanical drive software using a Windows-based operating system computer and the instructions

stored on the USB drive (P/N 063-0173-595) contained in the Raven Service Tool kit (P/N 117-0171-464).

When updating SmarTrax MD software, refer to the Raven Service Tool Installation Manual (P/N 016-5030-022)

located on the flash drive supplied with the installation kit. Software and manual updates are available on the

WARNING

Carefully read and follow all safety requirements

and precautions contained in this manual and the

machine-specific Installation Manual. Failure to

follow safety instructions may lead to equipment

damage, personal injury, or death.

«
...
10
11
12
13
14
...
»

Summary of Contents for SmarTrax MD









































































































































Reviews:

No comments

Related manuals for SmarTrax MD

Brand: salmson Pages: 12

Brand: uAvionix Pages: 4

MME100 - Audio Micro System

Brand: Magnavox Pages: 23

Point-of-Use Drinking Water System

Brand: R-Can Pages: 12

Brand: LENCO Pages: 66

Brand: Water Care Pages: 20

Brand: Plank Digital Audio Pages: 25

Brand: Pioneer Pages: 8

Brand: Pioneer Pages: 100

Brand: Pioneer Pages: 93

Brand: Pioneer Pages: 112

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 34

Brand: Panasonic Pages: 108

Brand: Panasonic Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands