Raven SmarTrax MD Calibration & Operation Manual Download Page 61

Page: 61 / 136

P/N 016-5030-020 Rev. D

VIPER PRO CALIBRATION AND OPERATION

8. Select

STEERING SWITCH CALIBRATION

IMPORTANT:

The switch on the bottom of the mechanical drive must be turned on before calibrating the steering

system.

FIGURE 24. Steering Switch Calibration Screen

1. Review the on-screen instructions and turn the steering wheel to verify proper operation.

NOTE:

The SmarTrax MD Setup Wizard will automatically advance to the next step in the calibration process

when the steering wheel is turned. If it does not, refer to Chapter 6, Troubleshooting for

troubleshooting information. If the problem persists, contact your local Raven dealer for further

information.

2. Proceed to Engage Switch Calibration below to continue with the system calibration.

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands