Raven SmarTrax MD Calibration & Operation Manual Download Page 21

Page: 21 / 136

P/N 016-5030-020 Rev. D

VIPER 4

2. Select

Serial Devices

3. Verify that the SmarTrax and SmarTrax GPS are listed in the Serial Device Setup screen.

NOTE:

If SmarTrax and SmarTrax GPS are not listed, press the Retry icon

on the bottom-right corner of

the screen. If these devices still do not appear, inspect cable connections to ensure they are installed

securely, then press the Retry icon again. If the devices still do not appear, refer to Chapter 6,

Troubleshooting for further information.

4. Press

Accept

5. Select

GPS Setup

6. Verify that SmarTrax on DGPS is visible and selected.

NOTE:

If SmarTrax GPS on DGPS is not visible and selected in the list, refer to Chapter 6, Troubleshooting

beginning on page 99 for further information.

Edit

GPS Setup

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Raven SmarTrax MD, Calibration & Operation Manual, Page: 21 / 136

Search results

Summary of Contents for SmarTrax MD

Reviews: