Raven SmarTrax MD Calibration & Operation Manual Download Page 48

Page: 48 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

INITIAL STARTUP

NOTE:

During the initial startup of the SmarTrax MD system, language data must be transferred from the

SmarTrax node to the Viper Pro. Allow the data transfer several minutes to occur before calibrating

the SmarTrax MD system.

SMARTRAX MD TERMS OF USE

The following Operator Liability Warning will be displayed on the Viper Pro screen when the SmarTrax MD system

is detected:

FIGURE 1. Operator Liability Warning Screens

The operator must select OK before the SmarTrax MD system may be enabled or calibrated. The Liability Waiver

screen will appear each time the Viper Pro is turned on or rebooted.

GPS CONFIGURATION

1. From the Home screen, select

Menu

2. Select

Setup

3. Select

Comm Port

. The following screen will appear:

SmarTrax MD is detected and turned on, but is not

enabled. Tap the foot/enable switch or touch the

steering wheel icon to enable the SmarTrax MD system.

SmarTrax MD is detected and in operation, with no

errors detected.

Display

Message

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands