Raven SmarTrax MD Calibration & Operation Manual Download Page 97

Page: 97 / 136

P/N 016-5030-020 Rev. D

ENVIZIO PRO AND CRUIZER II CONSOLES CALIBRATION AND OPERATION

FIGURE 32. OL Mode

NOTE:

The screen in Figure 33 illustrates an example of a situation in which SmarTrax MD is operating in OL

mode. This mode will remain active as long as the machine steers within 24 inches [60 cm] of the

displayed guidance line.

ADVANCED SETUP AND DIAGNOSTICS

This section provides detailed information on the various settings and options available in the SmarTrax MD

screens. The SmarTrax MD Settings screen may be accessed in two ways:
• From the Home screen, select the

Tools Menu

icon, then the Steering icon.

• In an active job, select

Next

in the SmarTrax MD sidebar.

FIGURE 33. SmarTrax MD Settings Screen

NOTE:

In Cruizer II software, the “3D Setup” option is displayed as “Terrain Comp”.

Guidance

Line

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Raven SmarTrax MD, Calibration & Operation Manual, Page: 97 / 136

Search results

Summary of Contents for SmarTrax MD

Reviews: