Raven SmarTrax MD Calibration & Operation Manual Download Page 66

Page: 66 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

1. Start a job and set a straight A-B guidance line.

NOTE:

Refer to the Viper Pro Installation and Operation Manual (P/N 016-0171-122) for information on

starting a job.

2. With the engine running at the operating RPM, drive forward at a speed of 5-7 mph [8-11 km/h].

FIGURE 30. SmarTrax MD Enable Icon

3. Enable SmarTrax MD by pressing the steering wheel icon on the Viper Pro display or by tapping the foot/

enable switch.

NOTE:

When SmarTrax MD is enabled, the steering wheel icon will turn green.

4. Allow SmarTrax MD to run while driving back and forth along the A-B guidance line.

NOTE:

If the machine is not operating to specifications, manual adjustment of the SmarTrax MD system may

be necessary. Refer to the Advanced Setup Tools section below information on adjusting the SmarTrax

MD system.

ADVANCED SETUP TOOLS

Are these necessary since they also appear in the Advanced Setup and Diagnostics section?

Advanced setup tools allow fine-turning of the system to adjust for operating conditions and improve steering

accuracy. To adjust the steering response on the Viper Pro, touch the SmarTrax area on the Viper Pro main menu.

The following screen will appear:

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands