manualshive.com logo in svg

Raven SmarTrax MD, Calibration & Operation Manual

Introducing the Raven SmarTrax MD, a cutting-edge precision steering system for agricultural machinery. Unleash its full potential by downloading the Installation Manual and step-by-step user guide, available for free download at manualshive.com. Seamlessly navigate your fields with confidence, maximizing efficiency and productivity at every turn.

Share
Download
background image

Table of Contents

P/N 016-5030-020 Rev. D

i

Chapter 1 

Important Safety Information.............................................................................  

1

General ............................................................................................................................................................................

1

Instructions for Wire Routing .................................................................................................................................

2

Chapter 2 

Introduction.............................................................................................................  

5

SmarTrax MD Part Identification ...........................................................................................................................

5

Installation ......................................................................................................................................................................

6

Recommendations .................................................................................................................................................................

6

Point of Reference .......................................................................................................................................................

6

Updates ...........................................................................................................................................................................

6

     Updating the Node .........................................................................................................................................................

6

Updating the Mechanical Drive ........................................................................................................................................

6

Chapter 3 

Viper 4.......................................................................................................................  

9

Widget and Button Definitions ..............................................................................................................................

9

Initial Startup ..............................................................................................................................................................

10

Data Transfer ..........................................................................................................................................................................

10

GPS Configuration ...............................................................................................................................................................

10

Internal GPS Receiver ..................................................................................................................................

10

External 600S GPS Receiver  ......................................................................................................................

12

External GPS Receiver  .................................................................................................................................

14

SmarTrax MD Terms of Use ..............................................................................................................................................

16

Machine Configuration ......................................................................................................................................................

16

Set Up Machine Profile(s) - Optional ....................................................................................................

16

Machine-Specific Configuration  .............................................................................................................

17

Calibrate the SmarTrax MD System ..................................................................................................................

18

Node Orientation .................................................................................................................................................................

19

Configuring Wheel Base and Antenna Offsets .........................................................................................................

19

Enhanced Tilt Calibration ..................................................................................................................................................

23

System Disengage Calibration ........................................................................................................................................

26

Engage Switch .......................................................................................................................................................................

27

Wheel Angle Sensor (WAS) Calibration .......................................................................................................................

27

Calibrate the Machine’s Steering System .......................................................................................................

28

Start a Job ...................................................................................................................................................................

29

System Adjustments ................................................................................................................................................

29

Line Acquisition (LA) Mode and Aggressiveness .....................................................................................................

30

On-Line (OL) Mode and Sensitivity ...............................................................................................................................

31

Advanced Setup Tools and System Diagnostics ..........................................................................................

31

System Information Tab ....................................................................................................................................................

31

Diagnostics Tab .....................................................................................................................................................................

33

Sensor Status .........................................................................................................................................................................

34

SmarTrax 3D Compensation Tab ....................................................................................................................................

35

GPS Setup Tab .......................................................................................................................................................................

36

Error Log Tab .........................................................................................................................................................................

37

Reset Calibration ..................................................................................................................................................................

37

Routine Operation ...................................................................................................................................................

38

Engage SmarTrax ..................................................................................................................................................................

38

Summary of Contents for SmarTrax MD









































































































































Reviews:

No comments

Related manuals for SmarTrax MD

Bang & Olufsen BeoSound 5 User Manual preview
BeoSound 5
Brand: Bang & Olufsen Pages: 20
Bang & Olufsen BeoSound 5 Manual preview
BeoSound 5
Brand: Bang & Olufsen Pages: 24
Bang & Olufsen BeoSound Ouverture User Manual preview
BeoSound Ouverture
Brand: Bang & Olufsen Pages: 44
Xflighttech AUTOPILOT / TRIM User'S Installation Manual preview
AUTOPILOT / TRIM
Brand: Xflighttech Pages: 44
Daewoo NC-8011 Service Manual preview
NC-8011
Brand: Daewoo Pages: 44
BIO-MICROBICS FAST Owner'S Manual preview
FAST
Brand: BIO-MICROBICS Pages: 12
Panasonic SC-HC38DB Operating Instructions Manual preview
SC-HC38DB
Brand: Panasonic Pages: 24
Panasonic SC-HC55DB Operating Instructions Manual preview
SC-HC55DB
Brand: Panasonic Pages: 24
Panasonic SC-HC412 Operating Instructions Manual preview
SC-HC412
Brand: Panasonic Pages: 28
Panasonic SC-HC58DB Operating Instructions Manual preview
SC-HC58DB
Brand: Panasonic Pages: 32
Panasonic SC-HC37DB Operating Instructions Manual preview
SC-HC37DB
Brand: Panasonic Pages: 20
Culligan Premier Series Installation, Operation And Service Instructions preview
Premier Series
Brand: Culligan Pages: 102
Marley Roots Rock Manual preview
Roots Rock
Brand: Marley Pages: 40
Teac MCDV72iP User Manual preview
MCDV72iP
Brand: Teac Pages: 16
Orbit 27752 Instructions preview
27752
Brand: Orbit Pages: 2
Grizzly HWW 3819 InoxInox Translation Of The Original Instructions For Use preview
HWW 3819 InoxInox
Brand: Grizzly Pages: 76
Aiwa NSX-SZ51 Service Manual preview
NSX-SZ51
Brand: Aiwa Pages: 18
Sterilight Viqua S2Q-OZ Owner'S Manual preview
Viqua S2Q-OZ
Brand: Sterilight Pages: 13

Brands by name

Popular brands

Load more brands