Raven SmarTrax MD Calibration & Operation Manual Download Page 40

Page: 40 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

Use the scroll button at the bottom of the Diagnostics prompt to toggle between the following PWM values and

steering system settings and options:

•

Disengage Sensitivity

- Proper tuning of the disengage sensitivity value allows the equipment operator to

disengage SmarTrax MD by turning the steering wheel with minimal or moderate effort. Disengage sensitivity

requires minimal adjustment.

NOTE:

If the sensitivity value is too low, the steering system may disengage in rougher fields without any

input from the operator. Raising the sensitivity value too high may make disengaging the SmarTrax

MD system at the steering wheel difficult or impossible.

•

Target Current and Actual Current

- Current readings performed on SmarTrax systems MD. Target Current is

what the system expects to read. Actual Current displays the amount of current the system is using to steer the

machine. These values are used to adjust system performance.

•

Current Compensation

- This feature is not used in SmarTrax MD systems.

•

Anti-Oscillation-Articulated Machines

- This feature is not used in SmarTrax MD systems.

SENSOR STATUS

Edit

SmarTrax MD

Sensor Status

Zero Yaw

Button

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands