Raven SmarTrax MD Calibration & Operation Manual Download Page 124 | Manualshive

Page: 124 / 136

background image

C

HAPTER

8

118

SmarTrax™ MD Calibration & Operation Manual

Technical Report No. /

Technischer Bericht Nr.:

Manufacturer /

Hersteller:

Type /

Typ:

13-00314-CC-GBM-00
Raven Industries
SmarTrax MD

AM-HZSF

Page /

Seite

: 8 / 14

4.3.1.

Examination of the Safety Functions /

Überprüfung der Sicherheitsfunktionen

The SmarTrax MD will be disengaged under the following conditions:

1.

The mechnical drive unit will be switched off with the master switch.
The controller SmarTrax MD Node and the monitor Cruizer II
Console are still active.

2.

The vehicle speed will exceed 45 kph.

3.

If the driver’s seat will be left (if a driver presence sensor is installed).

4.

If the steering wheel will be turned.

5.

Breakdown of the electric energy supply / the battery.

6.

If the ignition will be switched off.

7.

If the GPS signal will be lost longer than 5 sec.

If the SmarTrax MD will be disengaged automatically caused by one of the
above mentioned reasons a single warning tone sounds and a failure mes-
sage will be displayed on the monitor. /

«
...
122
123
124
125
126
...
»

Summary of Contents for SmarTrax MD









































































































































Reviews:

No comments

Related manuals for SmarTrax MD

CIRFLEXX UMS 4100

Brand: Grundig Pages: 38

Brand: Vizio Pages: 24

STAGE-4 ROKKER XXR Custom

Brand: J&M Corporation Pages: 5

Brand: Serenity Pages: 3

Brand: Boss Pages: 2

Brand: Panasonic Pages: 4

PM31 - SC Micro System

Brand: Panasonic Pages: 16

MW10 - 9.0" - Digital Photo frame

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 32

CDV100 - MINISYS 5-D DVD CHGR

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 99

Brand: Panasonic Pages: 102

Brand: Panasonic Pages: 134

Brand: Panasonic Pages: 448

Brand: Philips Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands