Raven SmarTrax MD Calibration & Operation Manual Download Page 108

Page: 108 / 136

HAPTER

102

SmarTrax™ MD Calibration & Operation Manual

No HC Pwr

High current power is not being

detected.

Check the high current cable

connections.
Check the fuse.

No HC Sync

The hardware inside the mechanical

drive is damaged.

1. Navigate to the SmarTrax Manual Steering

screen.

2. Toggle the master switch on and off,

verifying that the Raven LED logo

changes from white steady to blue

steady.

3. Drive the motor at various settings while

monitoring the Actual Current value. If no

current is drawn and the problem persists,

replace the mechanical drive.

No VTG

No VTGmessages are being received.

Check the receiver settings. The

recommended setting is 10Hz.

Oper Error

The operator presence switch has been

disconnected for more than seven

seconds.

Check the operator presence switch

connection to verify it is connected to

the operator presence switch or jumper

plug.

OpSW Fail

The operator has been out of the seat for

more than two seconds.

Return to the operator’s seat.
Check the operator presence switch

connections.

RsSw Fail

The foot/engage switch cable

connection has been disconnected.

Ensure the foot/engage switch cable

connection is connected to the node

harness.
Replace the foot/engage switch.

RsSw StOn

The foot/engage switch is stuck in the

“ON” position.

Ensure the foot/engage switch cable and

connection to the node harness is not

damaged.
Replace the foot /engage switch.

Swath Jmp

The guidance points being sent from the

field computer has jumped swaths,

causing the system to disengage.

Verify the guidance line on the field

computer is not switching between lines.

TC Error

3D terrain compensation has been

disabled because a gyro has failed but

SmarTrax MD may still be used.

Repair or replace the node when

convenient.

Too Fast

The vehicle speed is above 27 mph [45

km/h] and SmarTrax MD will be

disengaged in five seconds.

Decrease the vehicle speed.

Too FAST

The vehicle speed is above 29 mph [45

km/h] or has been above 27 mph for

more than 5 seconds and SmarTrax MD

has been disengaged.

Decrease the vehicle speed and re-

engage the SmarTrax MD system.

Too Slow

The vehicle speed is too slow and

SmarTrax MD has been disengaged.

Increase the vehicle speed and re-

engage the SmarTrax MD system.

Message

Possible Cause

Corrective Action

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands