manualshive.com logo in svg

Raven SmarTrax MD, Calibration & Operation Manual, Page: 5 / 136

Share
Download
Raven SmarTrax MD Calibration & Operation Manual Download Page 5

Table of Contents

P/N 016-5030-020 Rev. D

iii

Node Orientation .................................................................................................................................................................

77

Configuring Wheel Base and Antenna Offsets .........................................................................................................

77

Enhanced Tilt Calibration ..................................................................................................................................................

82

Steering Switch Calibration ..............................................................................................................................................

84

Engage Switch Calibration ................................................................................................................................................

85

Wheel Angle Sensor (SPS) Calibration .........................................................................................................................

86

Calibrate the Machine’s Steering System .......................................................................................................

86

Complete the SmarTrax MD Calibration Process .........................................................................................

88

Start a Job ...................................................................................................................................................................

89

System Adjustments ................................................................................................................................................

89

Line Acquisition (LA) Mode and Aggressiveness .....................................................................................................

89

On-Line (OL) Mode and Sensitivity ...............................................................................................................................

90

Advanced Setup and Diagnostics ......................................................................................................................

91

SmarTrax MD Information Screen .................................................................................................................................

92

Enhanced Tilt Calibration Setup Screen ......................................................................................................................

93

Advanced Setup Screen .....................................................................................................................................................

94

System Diagnostics Screen ...............................................................................................................................................

95

Reset Default ..........................................................................................................................................................................

97

Recalibrating Hydraulics ....................................................................................................................................................

97

Routine Operation ...................................................................................................................................................

98

Engaging SmarTrax MD .....................................................................................................................................................

98

System Settings   ..................................................................................................................................................................

98

Chapter 6 

Troubleshooting ................................................................................................... 

99

Node ..............................................................................................................................................................................

99

Mechanical Drive Diagnostics ...........................................................................................................................

100

Error Messages  .......................................................................................................................................................

100

SmarTrax MD Operation  ....................................................................................................................................

103

Chapter 7 

System Diagrams...............................................................................................  

107

Chapter 8 

Roadway Homologation Certification .......................................................... 

111

Summary of Contents for SmarTrax MD









































































































































Reviews:

No comments