Raven SmarTrax MD Calibration & Operation Manual Download Page 79

Page: 79 / 136

P/N 016-5030-020 Rev. D

ENVIZIO PRO AND CRUIZER II CONSOLES CALIBRATION AND OPERATION

4. Ensure all message sliders are turned off.
5. Select the green

Home

button in the lower-right corner of the screen.

6. Shut down and restart the Cruizer.
7. Select the

Tools Menu

icon on the main menu.

8. Select the

Show All

icon.

NOTE:

The light blue Steering icon should appear in the System row of the menu.

9. Inspect the SmarTrax node to ensure the data transfer is taking place.

IMPORTANT:

Allow the data transfer to complete before entering the steering menu. Failure to allow the data transfer to

complete may require a restart of the entire SmarTrax MD system. If the Rx and Tx lights on the SmarTrax

node are flashing rapidly, the data transfer is in progress. The Rx and Tx lights will flash slowly or turn off

when the data transfer is complete. This process typically takes around two minutes, but can take up to 20

minutes.

10. Proceed to SmarTrax MD Terms of Use section on page 74.

ENVIZIO PRO

DATA TRANSFER

During the initial startup of the SmarTrax MD system, language data must be transferred from the SmarTrax node

to the Envizio Pro. Allow the data transfer several minutes to occur before calibrating the SmarTrax MD system.

NOTE:

The Rx and Tx lights on the SmarTrax node will flashing rapidly during the data transfer. The Rx and Tx lights will

flash slowly or turn off when the data transfer is complete. Attempting to access the SmarTrax MD

configuration screen while language data is transferring will open a message asking the user to try again later.

NOTE:

The steps in this section apply only to Envizio Pro field computers that contain internal GPS. If internal

GPS is not present in the Envizio Pro, proceed to SmarTrax MD Terms of Use section on page 74.

GPS CONFIGURATION

FIGURE 2. Tools Menu

1. Select the

Tools Menu

icon on the Envizio Pro Home screen.

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands