Raven SmarTrax MD Calibration & Operation Manual Download Page 90

Page: 90 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

FIGURE 21. Finish Calibration

7. After the calibration is complete and the values on the screen have turned white, select

Finish Calibration

NOTE:

In order for the values to turn white, the COG value must be less than 10°, the Left/Right must be less

than 3 ft, and the Fore/Aft must be less than 3 ft. The rear wheels will not necessarily end up aligned

exactly with the markers to get the Fore/Aft number to turn black.

FIGURE 22. Calibration Complete

8. Select

Next

STEERING SWITCH CALIBRATION

IMPORTANT:

The switch on the bottom of the mechanical drive must be turned on before calibrating the steering

system.

Summary of Contents for SmarTrax MD








































































































































Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands

Raven SmarTrax MD, Calibration & Operation Manual

Search results

Summary of Contents for SmarTrax MD

Reviews:

Related manuals for SmarTrax MD

Brands by name

Popular brands