Omron ZW-7000 Series User Manual Download Page 78

Page: 78 / 336

Installation

ZW-8000/7000/5000

User's Manual

ZW-5000 Series

Extension fiber cable (option)

Connecting adapter (option)

• The connection adapter comes packed together with the extension fiber cable.

• Handling fiber cables

Refer to the following for information on how to handle fiber cables.

Remove the Fiber cable p.39

Model

Length

ZW-XF5002R

ZW-XF5005R

ZW-XF5010R

10m

ZW-XF5020R

20m

ZW-XF5030R

30m

Model

ZW-XFC2

Exten

ion fi

er c

ZW-XF50

：

（

2m/5m/10m/20m/

）

or He

er c

Connection

ptor

ZW-XFC2

Convex

ection

te the convex

ection of the fi

er connector with the

groove on the connection

pter

nd t

rn the thre

ded

ection clockwi

e while p

hing in.

When the fi

er in

ertion/fixing

crew i

not completely

tightened,

the c

e in the "No good"

in the fig

elow, optic

ign

nnot

e tr

mitted

nd correct

asu

rement i

not po

le.

Alw

check th

t the

tem i

in the "Good"

Groove

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands