Omron ZW-7000 Series User Manual Download Page 194

Page: 194 / 336

Checking the Information of the Sensor

192

ZW-8000/7000/5000

User's Manual

5-1 Checking the Information of the Sensor

Displays the information of the Sensor Controller and Sensor Head.



Multi View Explore

: [(ZW model name)] (double click)

→

Edit pane

: [General Settings] icon (

)

Item

Displayed item

Setting value

Description

General settings Sensor

information

Name

Displays the name of the Sensor Controller

Sensor Controller type

Displays the model information of the Sensor Controller.

Software Version

Displays the version information of the software of the Sensor
Controller.

Sensor head model

Displays the model information of the Sensor Head.

Sensor serial No.

Displays the serial No. of the Sensor Head.

MAC address

Displays the MAC address that is set.

Energization time

Displays the energization time of the Sensor Controller.

The Edit pane main pane is displayed in the

Edit pane.

You can check the above information under

[General settings] - [Sensor information].

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands